Panasonic DMR-BS750 - Manual (Page 47)

47
RQT9434
Playing
ba
ck
To enjoy High Bit Rate Audio and Video
This unit can decode High Bit Rate Audio (Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master Audio)
adopted in BD-Video.
To enjoy 7.1ch surround sound, the following conditions are necessary (Part shown in the shaded area of table given below).
≥Connect an amplifier/receiver with 7.1ch speaker supporting HDMI (High Bit Rate Audio) using a High Speed HDMI cable. (> 102)
≥Set “BD-Video Secondary Audio” to “Off”. (> 91)
≥Set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “Bitstream” or “PCM”. (> 91)
Connect an amplifier/receiver and confirm the desired audio type and necessary settings (“BD-Video Secondary Audio”, “Dolby D/Dolby D +/
Dolby TrueHD” or “DTS/DTS-HD”).
≥The number of channels listed is the maximum possible number of output channels.
≥Also, depending on the specifications or the settings of the amplifier/receiver, the results of the output may vary.
§1 When the connected equipment is not supported with these audio format, the audio is output as Dolby Digital bitstream, DTS Digital Surround
bitstream or down-mixed 2ch PCM (e.g., TV)
§2 [BD-V]: When playing BD-Video without secondary audio or clicking sound, the audio is output as the same format as if “BD-Video Secondary
Audio” was set to “Off”. (
> 91)
§3 When the connected equipment is not supported with multi channel surround, the audio is output as down-mixed 2ch PCM.
§4 [BD-V]: The audio is output as 5.1ch when “7.1ch Audio Reformatting” in the Setup menu (> 93) is set to “Off”.
§5 [BD-V]: The audio output is amplified from 5.1ch or 6.1ch to 7.1ch depending on the DTS, Inc. specifications regardless of the setting of ”7.1ch
Audio Reformatting” in the setup menu (
> 93).
§6 With PCM output, Dolby Digital EX becomes PCM audio decoded as Dolby Digital, DTS-ES recorded to DVD-Video becomes PCM audio
decoded as DTS Digital Surround, and DTS-ES recorded to BD-Video becomes PCM audio decoded as DTS-ES.
§7 [BD-V]: When “BD-Video Secondary Audio” is set to “On”, Dolby Digital EX is output as Dolby Digital and DTS-ES is output as DTS Digital
Surround, however if playing BD-Video without secondary audio or clicking sound, the audio is output as the original format.
[Note]
≥When setting “BD-Video Secondary Audio” to “Off”, the clicking sound on the menu and audio with secondary video in picture-in-picture mode
( > 46) cannot be output.
Many BD-Video movie contents are recorded in 24 frames/second in accordance with the film materials. However, they will normally be output in
60 frames/second in accordance with the display format.
These can be output in 24p as the original. Therefore, high-quality video can be enjoyed, such as the improved clarity, enhanced perspective, etc.
Preparation
≥Connect to a TV supporting 1080/24p input via an HDMI cable.
≥Set “BD-Video 24p Output” to “On”. (> 93)
Enjoying High Bit Rate Audio with 7.1ch speaker
About audio from audio output terminal
Terminal HDMI AV OUT DIGITAL AUDIO OUT
“Dolby D/Dolby D +/Dolby
TrueHD”/
“DTS/DTS-HD”
“Bitstream” §1 “PCM” §3 “Bitstream” “PCM”
“BD-Video Secondary
Audio”
“On” §2 “Off” “On” “Off” “On”/“Off” “On”/“Off”
Dolby Digital/
Dolby Digital EX §6
Dolby Digital/
Dolby Digital EX §7
Dolby Digital/
Dolby Digital EX
[DVD-V] 5.1ch PCM
[BD-V] 7.1ch §4
Dolby Digital/
Dolby Digital EX §7
Down-mixed 2ch
PCM
Dolby Digital Plus
Dolby Digital
Dolby Digital Plus
7.1ch PCM §2, 4 7.1ch PCM Dolby Digital
Dolby TrueHD Dolby TrueHD
DTS Digital Surround/
DTS-ES §6
DTS Digital
Surround/
DTS-ES §7
DTS Digital
Surround/
DTS-ES
[DVD-V] 5.1ch PCM DTS Digital
Surround
DTS-ES §7
[BD-V] 7.1ch PCM §5
DTS-HD High Resolution
Audio DTS Digital
Surround
DTS-HD High
Resolution Audio
7.1ch PCM §5
DTS Digital
Surround DTS-HD Master Audio DTS-HD Master
Audio
7.1ch LPCM
7.1ch PCM
Down-mixed 2ch
PCM
Regarding 24p output
DMRBS850&750EG-RQT9434-L_eng.book 47 ページ ２０１０年１月１４日 木曜日 午後４時２１分