Panasonic DMR-BS750 - Manual (Page 88)

88
RQT9434
Changing the unit’s settings
∫ Manual Tuning
You can add each new channels manually that the Auto Setup could
not complete successfully.
1 Press [
3, 4] to select the channel you want to set.
Transponder Frequency
Enter value with numbered buttons.
Symbol Rate
Press [ 2, 1] to select the auto and manual input of symbol
rate method.
≥Data flow transmission rate from the satellite to the dish.
Polarisation
Press [ 2, 1] to select the Polarisation method.
≥Polarisation indicates whether the transponder transmits the
satellite signal horizontally or vertically.
Modulation
Press [ 2, 1] to select the Modulation method.
Service ID
Press [ 2, 1] to select the Service ID method.
2 Press [OK] to start scan.
The set channel is displayed in the table.
3 Press [EXIT] and press [ W X CH] to check that applicable
channels have been selected.
∫ Update Channel List
You can update the satellite digital channels to receive to the latest
one.
1 Press [ 3, 4] to select “Update Channel List” and press [OK].
2 Press [ 3, 4] to select the method and press [2, 1] to select
settings.
≥Satellite
Satellite name is displayed.
≥Search Mode
All Channels:
Search for all channels.
Free Channels:
Search for free channels only.
≥Scan Mode
Quick:
In this mode, scanning takes place in a short period of time.
Full:
In this mode, the scanning is thorough but takes more time.
3 Press [OK].
The unit starts searching for newly available satellite digital
channels.
4 Press [RETURN ] to save the newly found channels.
∫ Signal Condition
You can check the quality and strength of digital broadcast signals.
Check the satellite dish if you are receiving a poor signal.
When “Signal Condition” is displayed in grey and cannot be
selected:
1 Press [EXIT] to exit the screen.
2 Press [INPUT SELECT] to select “TV”.
3 Display the Setup menu again (
> 87, Common procedures).
The quality and strength of the signal are shown.
Press [
W X CH] to select the channel.
Signal Input
Press [
2, 1] to select the terminal for which you wish to display the
signal condition.
Signal Quality
≥Below 2 (display red):
The signal quality is so poor that there may be interference in the
pictures and sound.
≥2–5 (display orange):
The signal quality is basically adequate, but brief interference in
the pictures and sound is possible in isolated case.
≥Over 5 (display green):
Optimum picture and sound quality.
Signal Strength
The display for signal strength is grey. “0” means signal strength is
0%, “10” means signal strength is 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your satellite dish.
≥When the signal is weak:
– adjust the position and direction of the dish.
– check that the current digital broadcast channel is correctly
broadcasting.
Satellite
Satellite name is displayed.
Parameter
Physical channel and frequency is displayed.
∫ Antenna System
You can receive several satellites if you have DiSEqC control
antenna system.
1 Press [ 3, 4] to select “Antenna System”.
2 Press [ 2, 1] to select antenna system and press [OK].
≥This unit supports DiSEqC Version 1.0.
∫ LNB Configuration
LNB
≥If you set to “One LNB” in “Antenna System”.
≥If you set to “MiniDiSEqC” in “Antenna System”.
≥If you set to “DiSEqC1.0” in “Antenna System”.
LNB Low Band Frequency (MHz)
LNB High Band Frequency (MHz)
Satellite
Set the connected satellite for the selected LNB.
≥If you do not know the connected satellite, select “No Satellite”.
(Available satellite will be searched in Auto Setup.)
≥If you select “User defined”, set “Test Transponder Frequency”
manually.
Test Transponder Frequency
Satellite
No.
Free TV:0 Pay TV:0 Radio:0
Searching
Quality Type Channel Name
Progress 0% 100%
RETURN
This will take about 10 minutes.
Update Channel List
Astra 19.2° E
“Finished” is displayed when the search is finished.
Channel Name 1 ZDF
Signal Input LNB in 1
Signal Condition
RETURN
Change Input Channel Up
Channel Down
Signal Strength 0 10
Signal Quality 0 10
Parameter 11836MHz, H, 27497kS/s
Satellite Astra 19.2° E
CH
[One LNB] Compatible with Single LNB
[MiniDiSEqC] Up to 2 LNBs can be controlled.
[DiSEqC1.0] Up to 4 LNBs can be controlled.
Not selectable.
[AA] [AB]
[AA] [AB] [BA] [BB]
[No Satellite] [Turksat 42°E] [Hellas 39°E]
[Astra 28.2°E] [Arabsat 26°E] [Astra 23.5°E]
[Astra 19.2°E] [Eutelsat 16°E] [Hot Bird 13°E]
[Eutelsat 10°E] [Eurobird 9°E] [Eutelsat 7°E]
[Sirius 5°E] [Intelsat 1°W] [Amos 4°W]
[Atl. Bird 5°W] [Atl. Bird 7°W] [Atl. Bird 8°W]
[Hispasat 30°W] [User defined]
DMRBS850&750EG-RQT9434-L_eng.book 88 ページ ２０１０年１月１４日 木曜日 午後４時２１分