Princeton Digital (USA) Guitar Effects Console G9.2tt2q - Manual (Page 38)

Effect Types and Parameters
ZOOM G9.2tt 74
PanDelay
This is a stereo delay with a delay time of up to 3000 ms.
PARM1 PARM2 PARM3 PARM4
Time 1 –
3000
FeedBack 0 – 100 HiDamp 0 – 10 Pan
L50 – L2,
0,
R2 – R50
Sets the delay time. Adjusts the feedback amount.
Adjusts the treble attenuation
of the effect sound. Adjusts the panning (left/
right) position of the sound.
PingPongDly
This is a ping-pong delay with a delay time of up to 3000 ms.
See PingPongEcho (next effect) for effect parameters.
PingPongEcho
This is a ping-pong type delay where the delay sound alternates between left and right. Long delay settings up to
3000 ms are possible.
PARM1 PARM2 PARM3 PARM4
Time 1 –
3000
FeedBack 0 – 100 HiDamp 0 – 10 Mix 0 – 100
Sets the delay time. Adjusts the feedback amount.
Adjusts the treble attenuation
of the effect sound.
Adjusts the level of the effect
sound mixed to the original
sound.
AutoPan
This effect cyclically moves the panning position of the sound.
PARM1 PARM2 PARM3 PARM4
Width
L50 – L2,
0,
R2 – R50
Rate 0 – 50 Depth 0 – 10 Wave 0 – 10
Adjusts the range of sound
position movement.
Adjusts the modulation rate. Adjusts the modulation depth.
Selects a waveform for
modulation. Higher setting
values result in stronger
clipping, which emphasizes
the auto-panning effect.
Effect Types and Parameters
ZOOM G9.2tt 75
TOTAL module
This module comprises parameters that affect the entire patch.
TOTAL
Specifies the patch specific tempo and the action of the function foot switches 1/2.
PARM1 PARM2 PARM3
Tempo 40 – 250 Function1 See page
38
Function2 See page
38
Specifies the patch specific
tempo (
→ p. 39).
Selects the action of function
foot switch 1. Selects the action of function
foot switch 2.
NAME
Specifies a name for the patch (→ p. 27).
ARRM
Makes settings for the ARRM function (→ p. 52). Use the [PAGE] key to switch between page 1 and 2.
PAGE1
PARM1 PARM2 PARM3
ARRM control target
min (minimum
value) See page
52
MAX
(maximum
value)
See page
52
Selects the ARRM control
target. When "NOT Assign" is
selected, the ARRM function
is disabled. Specifies the parameter value
that is set when the control
waveform reaches its lowest
point. Specifies the parameter value
that is set when the control
waveform reaches its highest
point.
PAGE2
PARM1 PARM2
Wave See page
53
Sync See page
53
Selects the control target
waveform.
Specifies control waveform
synchronization using the
patch specific tempo as
reference.
P1-1 to P1-4 (Expression pedal 1 setting)
Specify control targets 1 - 4 for expression pedal 1. Effect parameters are described below, after effect types.
P2V1 to P2V4 (Expression pedal 2, vertical direction setting)
Specify control targets 1 - 4 for expression pedal 2 (vertical direction).
P2H1 to P2H4 (Expression pedal 2, horizontal direction setting)
Specify control targets 1 - 4 for expression pedal 2 (horizontal direction).
The above 12 items have the same parameters. However, for P2H1 to P2H4 (pedal 2, horizontal direction setting), PARM4
(module on/off) is not available.
PARM1 PARM2 PARM3 PARM4
Expression pedal control
target
min (minimum value) MAX (maximum value) Module on/off function
Specifies the expression pedal
control target.
Specifies the parameter value
that is set when the pedal is
fully raised, or when pedal 2 is
fully turned to the left. Specifies the parameter value
that is set when the pedal is
fully pushed down, or when
pedal 2 is fully turned to the
right. Enables or disables the
module on/off function. This
parameter is not available for
P2H1 to P2H4 (pedal 2,
horizontal direction setting).