Setting up the remote control, 4 press setup to exit the preset mode, Recalling preset codes (vsx-709rds) – Pioneer VSX-709RDS User Manual

Page 22: Preparations, Dvd/ld player or dvd recorder, Tv , satellite tuner or cable tv tuner, Cd player, cd-r, tape deck or md recorder, Vcr or dvr (dvd recorder), Fm/am tuner

Advertising
background image

22

En

1 Press SETUP and hold for three seconds to

select the preset mode.

The LED will blink twice.
To cancel the preset mode
Press SETUP.

2 Press the MULTI CONTROL button for the

component you want to control.

Each button can be set to control one of the following components

DVD

: DVD/LD player or DVD Recorder

TV

: TV , Satellite tuner or Cable TV tuner

CD

: CD player, CD-R, Tape deck or MD recorder

CD-R

: CD player, CD-R, Tape deck or MD recorder

VCR

: VCR or DVR (DVD Recorder)

TVC

: TV , Satellite tuner or Cable TV tuner

TUN

: FM/AM tuner

3 Use the number buttons to enter the 4 digit

preset code.

The LED will blink after each digit is input and will blink twice to
confirm a valid code has been input.
If the LED shows one long blink it means an invalid code has been
input. Check the preset code list and try again. If you are not able to
input a preset code you can refer to page 24 to teach the remote
control individual commands.
Repeat steps 1 through 3 to recall preset codes for as many
components as necessary.

4 Press SETUP to exit the preset mode.

The remote control returns to the previous operation mode.
It will also return to the previous mode after ten seconds of inactivity.

• The RCV (Receiver) button cannot be preset.
• You can only input a code for the component type written on

each MULTI CONTROL button. See page 27 for information
on how to program a different type of component than speci-
fied on the button.

• If you recall a preset code for the tuner (TUN MULTI CON-

TROL), you will not be able to control the built-in tuner of this
receiver using the remote control. To reset the remote control
to the built-in tuner, input the preset code 0080.

Setting Up the Remote Control

In addition to controlling the receiver, the supplied remote control can operate your other components (DVD,
MD, VCR, TV, LD, CD, etc.). If your component(s) are listed in the “Preset Code List” on pages 58 to 65, simply
recall the corresponding preset code.

Recalling preset codes (VSX-709RDS)

The following steps show you how to recall preset codes for each MULTI CONTROL button. Once the preset
code is assigned, pressing the button will automatically set the remote control to operate the respective
component.

• Refer to “Preset Code List” on pages 58 to 62 for the components and manufacturers

available.

• Refer to “Controlling the Rest of Your System” on pages 52 to 55 for detailed explana-

tions on how to operate your other components.

3

2

1,4

Preparations

LED

Î

SOURCE

DISC

TV CONTROL

TV VOL

TVFUNC

TV

MENU

ENTER

D.ACCESS

BAND

CLASS

CH SELECT

CH LEVEL

AV PRE-PROGRAMMED AND LEARNING

REMOTE CONTROL UNIT

DSP

TEST TONE

FL DIMMER

LOUDNESS FUNCTION

SETUP

MUTING

MPX

DISPLAY

RF ATT

FQ

FQ

ST

ST

CHANNEL

MASTER VOLUME

MULTI CONTROL

DVD

TV

VCR

CD-R

RCV

CD

TUN

TVC

RECEIVER

7

4

¢

3

1

¡

8

2

MIDNIGHT

SIGNAL SELECT

EFFECT

+10

5.1CH

ATT

1

2

3

4

5

6

7

8

9

0

(

)

Advertising
This manual is related to the following products: