Pioneer VSX-709RDS - Manual (Page 24)

24
En
Learning mode: Programming signals from other remote controls
(VSX-709RDS only)
If preset codes are not available for your component(s), or the available preset codes do not operate correctly,
you can use this function to program in signals from the remote control(s) of your other component(s). This
operation can also be used after recalling a preset code to program additional operations not covered in the
preset codes.
1 Press SETUP and hold for three seconds.
The LED will blink twice.
2 Press the MULTI CONTROL button for the
component you want to control and then
press 9, 7, 5 to select the Learning setup
mode. The remote control is ready to learn
new commands from other remote controls.
The LED flashes rapidly
To cancel Learning setup mode
Press SETUP button.
After ten seconds if no commands are entered the remote
control will revert to its previous mode.
3 Press the button to be programmed (for
example the
3 [play] button).
4 Point the remote controls at each other, about
2 – 5 cm apart, and press the button on the
other remote control for the operation you
want to program .
1 Point the remote controls toward each other.
2 Press the button on the other remote control corresponding to the
operation you wish to program. The LED on this receiver’s remote
will go out and then blink twice when the operation is learned.
Press the teaching button repeatedly, varing the distances
between the remote, until you see this receiver’s remote blink
twice indicating the operation has been learned.
To program additional operations for the current component
Repeat steps 3 and 4.
To program operations for another component
Repeat steps 2 through 4.
5 Press SETUP to exit the Learning setup mode.
After ten seconds of inactivity the remote control will automatically
leave the Learning mode and revert to its previous mode.
2 2
1,5
2
2
Preparations
LED
2 – 5 cm
Î
SOURCE
ENTER
MIDNIGHT SIGNAL SELECT
TV CONTROL
TV VOL
TVFUNC TV MENU ENTER
D.ACCESS
BAND
CLASS
CH SELECT
CH LEVEL
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT DSP
TEST TONE
FL DIMMER
LOUDNESS
FUNCTION
SETUP
MUTING
MPX
DTV ON / OFF
DTV MENU
FQ FQ
ST
ST
CHANNEL
EFFECT MASTER VOLUME
DISC
+10
5.1CH
MALTI CONTROL
ATT
DVD
TV
VCR
CD-R
RCV
CD
TNU
TVC
RECEIVER
12
3
45
6
78
9
7
4
¢
3
1
¡
0
8 2
О
О
SOURCE
DISC
TV CONTROL
TV VOL TVFUNC
TV
MENU
ENTER
D.ACCESS BAND CLASS
CH SELECT CH LEVEL
DSP TEST TONE
FL DIMMER
LOUDNESS FUNCTION SETUP MUTING
MPX DISPLAY RF ATT
FQ
FQ
ST ST
CHANNEL
MASTER VOLUME
MULTI CONTROL
DVD TV VCR CD-R
RCV CD TUN TVC
RECEIVER
7 4 ¢
3 1 ¡
8
2
MIDNIGHT
SIGNAL SELECT EFFECT
+10
5.1CH ATT
1 2 3
4 5 6
7 8 9
0
Some commands from other remote controls cannot be learned,
but in most cases the remotes just need to be moved closer
together or farther apart.
The highlighted buttons
can learn new functions
( )
SOURCE
DISC
TV CONTROL
TV VOL TVFUNC
TV
MENU
ENTER
D.ACCESS BAND CLASS
CH SELECT CH LEVEL
DSP TEST TONE
FL DIMMER
LOUDNESS FUNCTION SETUP MUTING
MPX DISPLAY RF ATT
FQ
FQ
ST ST
CHANNEL
MASTER VOLUME
MULTI CONTROL
DVD TV VCR CD-R
RCV CD TUN TVC
RECEIVER
7 4 ¢
3 1 ¡
8
2
MIDNIGHT
SIGNAL SELECT EFFECT
+10
5.1CH ATT
1 2 3
4 5 6
7 8 9
0