Pioneer VSX-709RDS - Manual (Page 32)

32
En
Remote Control (VSX-609RDS)
Displays & Controls
1 MULTI CONTROL buttons
Use to put the receiver/remote control in the
stated mode.
For other equipment controls, see Controlling
the Rest of Your System on pages 52 – 55.
2 RECEIVER button (see page 15)
Use this button when setting up the surround
sound for the receiver.
3 Number/Mode buttons
(see pages 22, 43)
Use the number buttons to select the radio
frequency in tuner Direct access mode or the
tracks in CD, DVD mode etc.
Also, buttons marked with the following names
have special functions. If you try to use one of
these functions but the display flashes it means
that function cannot be used in the current mode
(for example DSP modes cannot be used when
5.1 CH setting is on).
2 (see pages 38, 39)
Use to put receiver in Dolby Digital, Dolby
Surround and DTS modes. To use first press the
RECEIVER button then operate this button.
DSP MODE (see pages 39)
Use to put receiver in one of the DSP modes. To
use first press the RECEIVER button then operate
this button.
MIDNIGHT (see page 41)
Use to put receiver in Midnight mode. To use,
first press the RECEIVER button, then operate
this button.
5.1 CH (see page 40)
When the DVD/LD or DVD 5.1 CH function is
selected each press switches the DVD/LD input
between DVD/LD and DVD 5.1 CH. To use, first
press the RECEIVER button, then operate this
button.
CHANNEL SELECT (see page 21)
Use to select a speaker when setting up the
surround sound of the receiver. To use, first press
the RECEIVER button, then operate this button.
TEST TONE (see page 21)
Use to sound the TEST TONE when setting up
the surround sound of the receiver. To use, first
press the RECEIVER button, then operate this
button.
ATT
Use to attenunate (lower) the level of an analog
input signal and prevent distortion (refer to p.34
!, @). To use, first press the RECEIVER button,
then operate this button.
CHANNEL LEVEL +/– (see page 21)
Use to set up the levels of the surround sound of
the receiver. To use, first press the RECEIVER
button, then operate this button.
SIGNAL SELECT (see page 36)
Use to select the proper signal (analog, digital) for
the source your are inputting. To use, first press
the RECEIVER button, then operate this button.
4 TV CONTROL buttons
The following four sets of buttons are dedicated
TV controls.
FUNC button
Use to select the TV function.
button
Use to turn on the power of the TV.
CH +/– buttons
Use to change channels on your TV.
VOL +/– buttons
Use to adjust the volume on your TV.
5 MENU button
Use to access different menus associated with
your DVD player.
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR CD
SOURCE CLASS MPX BAND
LOUDNESS FUNCTION MUTING
RECEIVER
D.ACCESS
ATT
VOL
MENU
TOP
MENU
VOL
CH
2 DSP MODE MIDNIGHT 5.1CH
CD-R/
TAPE/MD
CHANNEL
SELECT
CHANNEL
LEVEL EFFECT
ENTER
FQ
FQ
ST ST
FL
DIMMER
REMOTE
SETUP
MASTER
VOLUME
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
TV CONTROL
FUNC
10 DISC
SIGNAL
SELECT
TEST
TONE
RECEIVER TUNER TV CONT
Î
1 2 3 4
1 ¡ 4 ¢
7 8 3
5 6 7 8
9 0
CHANNEL
DISPLAY RF ATT
2
6
8
5
1
3
0
9
-
=
!
@
~
#
%
$
^
7
4