Port-A-Cool KA55 - Manual (Page 3)

2 3
®
manufactured by port-a-cool, llc
Port-A-Cool Mexico, S. de R.L. de C.V.
•
Paseo de la Reforma #404 piso 4
•
Col. Juárez
México DF 0660
•
www.KuulAire.com
Port-A-Cool, LLC
•
709 Southview Circle
•
Center, TX 75935
•
www.KuulAire.com
2 3
2 3 2 3
®
manufactured by port-a-cool, llc
Port-A-Cool, LLC
U
709 Southview Circle
U
Center, TX 75935
U
www.kuulaire.com
Port-A-Cool Mexico, S. de R.L. de C.V.
U
Paseo de la Reforma #404 piso 4
U
Col. Juárez
México DF 06600 U
www.kuulaire.com
WARNINGS AND SAFETY RULES 

!
LOCATION
PARTS DESCRIPTION 



ELECTRICAL
ASSEMBLY INSTRUCTIONS
WARRANTY
CLEANING AND MAINTENANCE
TROUBLESHOOTING
USE AND OPERATION

!
POWER
2. Press the POWER button to turn on the unit. To turn off
the unit, press the POWER button again. When the POWER
SPEED
Press the SPEED button to select the desired fan speed. The
selected fan speed will be shown on the display.
Low speed
Medium speed
COOL
To use the unit as an evaporative cooler, press the COOL button,
the pump will turn on and distribute water to wet out the
LOW WATER ALARM FUNCTION
KA55 is equipped with a low water alarm sensor. When water
tank with water, low water alarm will engage again.
TIMER
SWING
Press the SWING button to direct the air stream. The louvers will
UP-DOWN AIR FLOW
To adjust the vertical direction of air flow, adjust the horizontal
outflet louvers manually.
FPO 2
DISPLAY & CONTROL PANEL
WARNINGS AND SAFETY RULES


!
LOCATION
PARTS DESCRIPTION 



WARRANTY
CLEANING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
TROUBLESHOOTING
REMOTE CONTROL
USE AND OPERATION

!
1.
SPEED
High speed
cellulose cooling pad located in the rear of the unit.
After approximately three minutes, as the
pad becomes saturated, the air from the outlet should be cool.
Connect the power cord to a power outlet. The POWER
button will light up in red with audible sound indicating
power source is connected. The unit is in standby mode.
button is pressed, blue LCD display and the SPEED
button will light up and cooler will start in fan mode at
a medium speed then drop to low speed setting.
The COOL button will light up and COOL symbol will appear
in the display.
in the tank is below minimum level, LOW WATER ALARM
function is activated. When the function is activated, audible
warning will sound for 10 seconds and the COOL button and
the LOW WATER icon in the display will continuously flash.
At the same time, the power to the pump will be cut off to protect
the life of the pump. In order to disengage the function, turn off
and unplug the unit from the power outlet, and fill the tank with
water above the minimum level. In order to turn off the alarm
function and continue to use it in FAN mode, turn off the unit
and turn the unit back on. If COOL button is pressed again without
filling the
begin to move automatically from side to side. When the SWING
button is pressed, the button will illuminate and the SWING
icon will appear in the display
KA55 comes with an 8-hour timer. To set, press
TIMER button to the desired operation time. TIMER
button is illuminated and the remaining operational time
is shown on the display. When the pre-selected time
has passed, the unit will automatically shut off.
SLEEP
When the SLEEP button is pressed, the fan speed will
remain/chage to HIGH and run for 1hr, MEDIUM speed for
1hr and will change to LOW speed and remain. When the
SLEEP button is pressed, the button will illuminate and the
SLEEP symobol will appear in the display.
POWER
1. Connect the power cord to a power outlet. The POWER button
will light up in red with audible sound indicating power source
is connected. The unit is in standby mode.
2. Press the POWER button to turn the unit on. To turn off the
unit, press the POWER button again. When the power button
is pressed, blue LCD display and the SPEED button will light
up and cooler will start in fan mode at a medium speed then
drop to low speed setting.
SPEED
Press the SPEED button to select the desired fan speed. The
selected fan speed will be shown on the display.
LOW Speed
MEDIUM Speed
HIgH Speed
COOL
To use the unit as an evaporative cooler, press the COOL button,
the pump will turn on and distribute water to wet out cellulose
cooling pad located in the rear of the unit. The COOL button
will light up and COOL symbol will appear in the display. After
approximately three minutes, as the pad becomes saturated,
the air from the outlet should be cool.
LOW WATER ALARM FUNCTION
The KA55 is equipped with a low water alarm sensor. When water
in the tank is below minimum level, LOW WATER ALARM function
is activated. When the function is activated, audible warning will
sound for 10 seconds and the COOL button and the LOW WATER
icon in the display will continuously flash. At the same time, the
power to the pump will be cut off to protect the life of the pump.
In order to disengage the function, turn off and unplug the unit
from the power outlet, and fill the tank with water above the
minimum level. In order to turn off the alarm function and
continue to use it in FAN mode, turn off the unit and turn the
unit back on. If COOL button is pressed again without filling the
tank with water, low water alarm will engage again.
TIMER
The KA55 comes with an 8-hour timer. To set, press TIMER button
to the desired operation time. TIMER button is illuminated and
the remaining operational time is shown on the display. When the
pre-selected time has passed, the unit will automatically shut off.
SWING
Press the SWINg button to direct the air stream. The louvers will
begin to move automatically from side to side. When the SWINg
button is pressed, the button will illuminate and the SWINg icon
will appear in the display.
UP-DOWN AIR FLOW
To adjust the vertical direction of air flow, adjust the horizontal
outlet louvers manually.
SLEEP
When the SLEEP button is pressed, the fan speed will remain/
change to HIgH and run for 1 hour, MEDIUM speed for 1 hour
and will change to LOW speed and remain. When the SLEEP
button is pressed, the button will illuminate and the SLEEP
symbol will appear in the display.
DISPLAY & CONTROL PANEL
WARNINGS AND SAFETY RULES
▲
!
LOCATION
PARTS DESCRIPTION �
�
ELECTRICAL
ASSEMBLY INSTRUCTIONS
WARRANTY
CLEANING AND MAINTENANCE
NOTES
TROUBLESHOOTING
REMOTE CONTROL
USE AND OPERATION
▲
!
WARNINGS AND SAFETY RULES
▲
!
LOCATION
PARTS DESCRIPTION �
�
ELECTRICAL
ASSEMBLY INSTRUCTIONS
WARRANTY
CLEANING AND MAINTENANCE
NOTES
TROUBLESHOOTING
REMOTE CONTROL
USE AND OPERATION
▲
!
www.sylvane.com 1-800-934-9194