Pioneer DJm-909 - Manual (Page 19)

19
<DRB1349>
EFFECT FUNCTIONS
Types of Effects
This unit is equipped with a beat effector linked to the BPM, and fader effector linked to the channel or cross fader, producing a total
of 50 basic effects, but an even wider variety of effects can be produced by varying the parameters of each effect.
Beat Effector (effects linked to BPM)
Name
1 DELAY (*1)
2 ECHO (*1)
3 PAN ECHO (*1)
4 PITCH ECHO (*1)
5 REVERSE DELAY (*1)
6 DUCKING ECHO (*1)
7 ROLL (*2)
8 HOLD ECHO (*1) (*2)
9 MULTI TAP DELAY (*1)
10 RAIN (*1)
11 REVERB1 (*1)
12 REVERB2 (*1)
13 REVERB3 (*1)
14 PITCH SHIFTER1
15 PITCH SHIFTER2
16 PAN
17 TRANS
18 RHYTHM TRANS
19 TRANS PAN
20 TREMOLO
21 VIBRATO
Function
In time with BPM, outputs repeat sound once.
In time with BPM, outputs repeat sound
several times, while diminishing.
In time with BPM, outputs repeat sound,
alternately to left and right.
In time with BPM, outputs repeat sound
while changing pitch.
In time with BPM, outputs repeat sound in
reverse of playback direction.
Outputs repeat sound when input sound level
drops below a certain point.
With the turning ON of the EFFECT switch as
a trigger, the input sound is recorded, and the
recorded sound is repeated in units of
individual beat.
In time with BPM, outputs repeat sound several
times while diminishing. Repeat sound is
preserved even if EFFECT switch is turned OFF.
Output delay sound in time with beat, at
intervals of preset delay time.
Outputs sound with feeling of being in water.
Produces reverberation sound similar to that
of a garage-sized room.
Produces reverberation sound similar to that
of a large hall.
Hall reverberation (echo) is added to sound
lag timed to BPM.
Allows changing of pitch within range of ± 1
octave.
Outputs three types of pitches together with
preset pitches.
In time with BPM, outputs sound alternately
to left and right.
In time with BPM, cut sound.
Cut sound in time with BPM and preset
pattern.
In time with BPM, cut long-period PAN
outputs at set time.
Produces wavering sound by applying tonal
modulation.
Apply modulation to frequency, thus
producing tonal variation.
FX ADJ. Parameter (touch panel)
Set delay time of 1/8 to 8/1 of each beat of BPM.
Set delay time of 1/8 to 8/1 of each beat of BPM.
Set delay time of 1/8 to 8/1 of each beat of BPM.
Set delay time of 1/8 to 2/1 of each beat of BPM; and
set pitch shifter up or down.
Set delay time of 1/8 to 8/1 of each beat of BPM.
Set delay time of 1/8 to 8/1 of each beat of BPM.
Set effect time of 1/8 to 8/1 of each beat of BPM.
Set delay time of 1/8 to 8/1 of each beat of BPM.
Set delay time of 1/4 to 1/1 of each beat of BPM; select
delay pattern; and set feedback ON/OFF.
Set delay time of 1/8 to 8/1 of each beat of BPM.
8 patterns can be set based on different filters.
8 patterns can be set based on different filters.
Set delay time of 1/8 to 4/1 of each beat of BPM.
Set amount of pitch shift.
Set type of changing pitch harmonies.
Set right-left allocation time in units of 1/8 to 8/1 of each
beat of BPM.
Set cut time in units of 1/8 to 8/1 of each beat of BPM.
Set effect time of 1/2 to 2/1 of each beat of BPM; and
select cut pattern.
Set cut time in units of 1/16 to 1/1 of each beat of BPM;
and set PAN period.
Set modulation period based on beats calculated from
BPM.
Set modulation period based on beats calculated from
BPM.
(*1) When the channel fader or cross fader is used to lowering sound volume, no effect sounds will be heard, even if monitor
SELECT switch is set to the [EFFECT] position.
(*2) When EFFECT switch is turned OFF, no effect sounds will be heard even if the monitor SELECT switch is set to the [EFFECT]
position.