Panasonic CQ-C5305U - Manual (Page 12)

CQ-C5405U/C5305U 22 CQ-C5405U/C5305U 23
English
Function Setting
Audio Setting, Function Setting
1
Hold down [VOL] (PUSH
SEL: Select) for 2 sec. or
more to open the menu.
2
Press [VOL] (PUSH SEL: Select) to
select a mode to be adjusted.
3
Turn [VOL] clockwise
or counterclockwise to
adjust.
Notes:
• The sequence and contents of setting items may
depend on the conditions of devices to be connected.
For further information, refer to the System Upgrade
Guidebook or the instruction manuals for the devices
to be connected.
• To return to the regular mode, press [DISP].
• If no operation takes place for more than 5 seconds
in function setting, the display returns to the regular
mode.
Demonstration
You can set up the monitor to display or hide the
demonstration screen.
: On (Default)
: Off
Note: Button operation with either the main unit or
remote control allows users to cancel the demonstration
screen for 20 seconds and enable the selected operation
even in the demo-on mode.
Display Color Selection
You can select display color.
Default: OCEAN (aqua blue)
Variety: OCEAN (aqua blue), SKY (sky blue), FOREST
(green), ORANGE (amber), FIRE (red), PINK (deep pink),
ROSE (pink), STORM (7 colors)
OCEAN (aqua
blue)
ORANGE
(amber)
STORM
(7 colors)
Mute/Attenuation
You can select mute or attenuation.
: Volume down by
10 steps
: Volume off (Default)
AUX1 Skip
If AUX1 is not used, the AUX1 mode is skipped when
selecting the source.
: On (Skip disabled.)
(Default)
: Off (Skip enabled.)
Function Menu Display
Audio Setting
1
Press [VOL] (PUSH
SEL: Select) to open
the menu.
2
Press [VOL] (PUSH SEL: Select) to
select a mode to be adjusted.
3
Turn [VOL] clockwise
or counterclockwise to
adjust.
Notes:
• The sequence and contents of setting items may
depend on the conditions of devices to be connected.
For further information, refer to the System Upgrade
Guidebook or the instruction manuals for the devices
to be connected.
• To return to the regular mode, press [DISP].
• If no operation takes place for more than 5 seconds
in audio setting (2 seconds in the volume adjustment,
10 seconds in the SQ adjustment), the display returns
to the regular mode.
• The volume can also be adjusted directly using [VOL]
on the main unit. (  page 12)
• Please refer to page 13 for calling up a preset SQ.
Volume Adjustment
(Setting range: 0 to 40, Default: 18)
: Up
: Down
Bass Adjustment
(Setting range: 12 dB to 12 dB, 2 dB Step, Default:
Bass 0 dB)
: Up
: Down
Treble Adjustment
(Setting range: 12 dB to 12 dB, 2 dB Step, Default:
Treble 0 dB)
: Up
: Down
Note: Do not activate SQ and Bass/Treble at the same
time to avoid causing sound distortion.
SQ Adjustment
(  page 13)
(Adjustable frequency: 12 dB to 12 dB (by 2 dB))
Setting range:
SQ Low/Bass: ±12 dB (at 60 Hz, 80 Hz, 100 Hz,
200 Hz)
SQ Mid: ±12 dB (at 500 Hz, 1 kHz, 2 kHz,
3 kHz)
SQ High/Treble: ±12 dB (at 8 kHz, 10 kHz, 12 kHz,
15 kHz)
Balance Adjustment
(Setting range: L (left) 15 to R (right) 15 and Center,
Default: Center)
: Right enhanced
: Left enhanced
Fader Adjustment
(Setting range: R (rear) 15 to F (front) 15 and Center,
Default: Center)
: Front enhanced
: Rear enhanced
Subwoofer Level Adjustment
(Setting range : mute ( ), 6 dB to 6 dB, 2 dB
Step, Default: 0 dB)
: Up
: Down
Subwoofer Low Pass Filter
(Setting range: 80 Hz, 120 Hz, Default: 80 Hz)
: 120 Hz
: 80 Hz
Re-master Setting
High-range signal lost through MP3/WMA/AAC
compression is reproduced to more closely recreate the
pre-compression sound.
(Setting range: On/Off, Default: On)
: On
: Off
Notes:
• At high bit rates, the Re-master function may have
little effect.
• It is only effective for playback of MP3/WMA/AAC data.
Adjustment to each speaker and an optional subwoofer
Audio Menu Display