Panasonic CQ-C5305U - Manual (Page 6)

CQ-C5405U/C5305U 10 CQ-C5405U/C5305U 11
English
Preparation Before Initial Use
Pull the insulation fi lm
out from the backside of
remote control gently.
Battery Replacement
 Remove the battery
holder with the remote
control unit placed on a
fl at surface.
 Stick your thumbnail
into the groove, and
push the holder in
the direction of the
arrow, and at the
same time.
 Pull it out in the
direction of the
arrow using a tough
pointed object.
 Put a battery in the case
with ( ) side facing up.
 Put the case back.
Preparation
Preparation, General
The demonstration message appears for initial use.
1
Set your car’s ignition switch to the
ACC or ON position.
2 Press [PWR] (Power).
3
Hold down [VOL] (PUSH SEL: Select)
for 2 sec. or more to open the menu.
4
Press [VOL] (PUSH SEL: Select) to
select the Demonstration setting.
(“DEMO” is displayed)
5 Turn [VOL] counterclockwise.
For using the remote control, press [0] ( ).
Notes:
• To return to the regular mode, press [DISP].
• Refer to the section on “Function Setting” (
 page
23).
• When “NO DISC” is displayed, the Demonstration
cannot be cancelled.
Cancellation of Demonstration
Remote Control Preparation
Tough pointed object
Back side
The 12-hour system is used for the clock.
1
Press [PWR] (Power).
2
Press [DISP].
3
Hold down [DISP] for 2 sec. or more.
4
Adjust the hour and press [DISP].
[ ]: Forward
[ ]: Backward
5
Adjust the minute and press [DISP] to
confi rm the adjustment.
[ ]: Forward
[ ]: Backward
Notes:
• Adjust the clock when “ADJUST” appears on the display.
• Hold down [
] or [] to change numbers
rapidly.
• When “NO DISC” is displayed, the clock cannot be
adjusted.
General
This chapter explains how to turn on or off the power, how to adjust the volume, etc.
Power On
Press [PWR] (Power).
Power Off
Hold down [PWR] (Power) for 1 sec. or
more.
You can remove the face plate to
prevent it from being stolen.
Removing
1
Turn off the power. (  above)
2 Press [OPEN]. The face plate will be
opened.
3
Push the face plate to the
left.
4
Pull it out toward you.
5 Put the face plate in
the case.
Cautions
• This face plate is not waterproof. Do not expose it to
water or excessive moisture.
• Do not remove the face plate while driving your car.
• Do not place the face plate on the dashboard or
nearby areas where the temperature rises to high.
• Do not touch the contacts on the face plate or on
the main unit, since this may result in poor electrical
contacts.
• If dirt or other foreign substances get on the
contacts, wipe them off with clean and dry cloth.
• To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
Power On/off
(PWR: Power)
Face Plate Removing/Mounting
(Anti-Theft System)
Display Change
(DISP: Display)
Cautions
• Remove and dispose of an old battery immediately.
• Do not disassemble, heat or short a battery. Do not
throw a battery into a fi re or water.
• Follow local regulations when disposing of a
battery.
• Improper use of a battery may cause overheating,
an explosion or ignition, resulting in injury or a fi re.
Warning
Keep batteries and insulation fi lm out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under normal use
(at room temperature)
Insulation fi lm




Clock Adjustment
The display changes as follows every time [DISP] is
pressed.
At Power-off:
Clock display (Default)
Display Off
Mounting
1 Fit the face plate with its left hole on the
left pin provided on the main unit.
2
Fit the other hole on the other pin
applying slight pressure.
At Power-on:
When the power is set to ON, refer to the description for
each source mode.
Notice
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material - special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.