Error messages, Helpful hints, Before requesting service – Panasonic NV-VP32 User Manual
Page 45
Helpful Hints
45
Before Requesting Service
Disc picture
Editing
On-screen display
Self-diagnostic Indications on the unit’s display
Picture distorted.
≥Some distortion is normal during search.
—
There is ghosting when
progressive output is on.
≥Change “Video Output Mode” in Picture Menu to “480I”. This problem is caused by the
editing method or material used on DVD-Video, but should be corrected if you use interlace
output.
Picture quality is poor.
≥Check the settings in the On-Screen Menu “Picture Menu”.
39
Menus not displayed correctly.
≥Change the zoom ratio to “k1.00”.
≥Set the subtitle position to 0.
≥Go to “Video” in the SETUP menu, and change “TV Aspect” to suit your TV.
37
34
41
Black bands appear in the
recording.
≥Move the other equipment away from the TV as it may be picking up interference.
—
Recording video or audio from
external equipment is not
possible.
≥The connections were done incorrectly. Check the connections to the other equipment.
≥The external input channel “A1” or “A2”, to which the player is connected is not selected.
Press [INPUT SELECT] to select “A1” or “A2”.
A video was dubbed, but the
video is distorted or the colours
are abnormal.
≥Copy-protected material was dubbed.
Copy-protected materials cannot be recorded normally.
Most commercially available videotapes and DVD discs (including rental soft tapes/DVDs)
are copy-protected so that illegal dubbing is impossible.
—
The audio level on the DVD
section is not corresponding to
that on the VHS section after
editing.
≥Some discs may reproduce different audio levels.
If the audio in particular parts, such as speech, is set to a low or high level, it may be
recorded on a video cassette at a high or low level, respectively.
—
Error Messages
PLEASE PUT IN A VIDEO
CASSETTE.
≥[REC¥] or [TIMER
] has been pressed without a video cassette inserted. Insert a video
cassette with an intact erasure prevention tab.
PLEASE STOP THE TAPE.
≥TUNER PRESET has been selected during playback. Stop the tape.
PLEASE USE A CASSETTE
WITH TAB.
≥[REC¥] or [TIMER
] has been pressed without a video cassette with an intact erasure
prevention tab. Use a video cassette with an intact erasure prevention tab.
NO TIMER RECORDING
HAS BEEN SET.
≥[TIMER
] has been pressed with no timer programmes.
Set timer recording.
Cannot display group xx,
picture xx
≥You are trying to display incompatible pictures.
—
The progressive out is set
to “Disable”
≥Go to “Video” in the SETUP menu, and select “Enable (NTSC Disc Only)” in “Progressive Out
(Component)”.
H
∑∑, F∑∑
(
∑∑ stands for a number.)
≥An error has occurred. The number following “H” or “F” depends on the status of the unit.
Reset procedure:
Press [
Í/I] to switch the unit to the standby mode and then back to ON.
Alternatively, press [
Í/I] to switch the unit to the standby mode, disconnect the AC mains lead,
and then reconnect it.
≥If the service numbers fail to clear, note them and contact a qualified service person.
—
—
CHECK DISC
≥Disc is dirty. Wipe it clean.
≥You inserted a DVD-R which is not finalized.
No DISC
≥You haven’t inserted a disc; insert one.
≥You haven’t inserted the disc correctly; insert it correctly.
—
No PLAY
≥You inserted a disc the unit cannot play.
≥You inserted a blank DVD-RAM.
≥A disc whose playback is restricted in the SETUP menu is inserted.
Change the “Ratings” setting.
—
VP32GL.book 45 ページ ２００４年６月１１日 金曜日 午後４時３２分