NEC MultiSync XG-1352 - Manual (Page 25)

25
BASIC OPERATION
NOTE:
• While you are viewing a source screen, you can also select the input signal directly by pressing the INPUT “1” through “10”
button. In this case INPUT buttons function as follows:
When using the projector in stand alone operation:
Input Module
RGB VIDEO S–VIDEO
1
4
7
–
–
2
4
7
4
7
A 3
5
8
5
8
B
C
B
C
With RGB board
With VIDEO board
Standard
Optional
(XGRGBIN(A))
Optional
(XGVIDIN(B))
Input Mode
*When INPUT “1” button is selected, RGB and COMPONENT signals are retrieved in this order; when INPUT “10” button is
selected, a COMPONENT signal is retrieved only.
Numbers designate INPUT buttons on the remote control.
When using the projector with the ISS-6020/ISS-6020G:
INPUT 1 through 10
→
Selects the corresponding number slot of the ISS-6020/ISS-6020G
When using the projector with two ISS-6020/ISS-6020G or more:
To switch to another input signal, enter the master slot number, then the slave slot number by using INPUT buttons and press
ENTER.
Example:If you want to select a signal from the no.3 slot of the slave Switcher which is connected to the no.2 slot of the master Switcher, first
press the INPUT “2” button, then the INPUT “3” button and then press ENTER.
• You can switch to any input signal of NO 01 through10 on the INPUT SELECT list by holding down the CTL button and pressing
one of the INPUT buttons corresponding to the input number. To activate this function you must first select ENABLE in the
DIRECT ENTRY ACCESS mode. For further details, contact your dealer.
• If there are two or more memory locations that contain the same signal information the projector will reference the signal nearest
the beginning of the list. To select the next signal use the CURSOR or button and press ENTER.
P 0 1 / 1 0 – 2 I N P U T S E L E C T
S T A N D A L O N E
N O
0 1
0 2
0 3
0 4
0 5
0 6
0 7
0 8
0 9
1 0
F H
1 5 . 7 4 k H z
1 5 . 7 4 k H z
1 5 . 7 4 k H z
1 5 . 7 4 k H z
4 8 . 6 0 k H z F V
6 0 . 0 0 H z
6 0 . 0 0 H z
5 0 . 0 0 H z
5 0 . 0 0 H z
6 0 . 0 0 H z D A T E
0 0 / 0 0 / 0 0
0 0 / 0 0 / 0 0
0 0 / 0 0 / 0 0
0 0 / 0 0 / 0 0
0 0 / 0 0 / 0 0
P 0 1 / 1 0 – 1 I N P U T S E L E C T
S T A N D A L O N E
N O
0 1
0 2
0 3
0 4
0 5
0 6
0 7
0 8
0 9
1 0
S O U R C E
V I D E O
V I D E O
V I D E O
V I D E O
R G B I N P U T
A
A
A
A
A N A M E
N T S C 3 . 5 8
N T S C 4 . 4 3
P A L
S E C A M
V E S A 1 0 2 4
ᮤ ᮣ
Signal name
Input terminal
Entry date Rgistered input module
Connect condition of the Switcher
Vertical
Frequency Horizontal
Frequency
Page / total pages – sheet No.
INPUT SELECT List Format
OUTPUT DATA : LIST NO. ✻ ✻
OUTPUT DATA : LIST NO. ✻ ✻
Output data for the signal currently projected.
COMPONENT
1*/10
4
7
–
–