NEC R 37 Xtra - Manual (Page 23)

23
36
35
RGB Controls Group
The RGB Controls allow you to adjust the color temperature and the white
balance for RGB input.
COLOR TEMP. : Pressing + selects the color temperature: 10500 K, 9300K,
6500K or custom.
Pressing the PROCEED key proceeds to the RGB gain and bias adjustment.
This adjustment allows you to adjust the white balance.
R, G, B-GAIN : Pressing + or - increases or decreases the gain level for each color.
R, G, B-BIAS : Pressing + or - increases or decreases the bias level for each color.
OSM Location/OSM Display Time Control
You can choose where you would like OSM image to appear on your screen.
Selecting OSM location allows you to manually adjust the OSM menu left,
right, up, or down. The OSM menu will stay on as long as it is in use. In the
OSM Turn Off Time submenu, you can select how long the monitor waits after
the last touch of a key to shut off the OSM menu. The preset choices are 5,
10, 30, and 120 seconds. Note that 30 seconds is the factory preset.
OSM H-POSITION : Pressing + or - moves the OSM menu right or left.
OSM V-POSITION : Pressing + or - moves menu up or down.
OSM DISPLAY TIME : Pressing + or - selects the preset time in increasing or
Source Information
Source Information provides you information about the current resolution
display and technical data including the horizontal and vertical frequency.
NOTE: These adjustments are for RGB mode only.
H-FREQ : indicates the horizontal frequency of the current input signal.
V-FREQ : indicates the vertical frequency of the current input signal.
H-POL : indicates the polarity of the horizontal sync. signal.
V-POL : indicates the polarity of the vertical sync. signal.
NEG : indicates the polarity is negative.
POS : indicates the polarity is positive.
R G B DV
C O L O R T E M P .
R G B DV
C O L O R T E M P .
P R E S S ' P R O C E E D ' F O R
R G B G A I N / B I A S S E T T I N G S
1 2 3 1 0 5 0 0 ˚ K
R G B DV
R - G A I N ( W H I T E L E V E L )
G - G A I N ( W H I T E L E V E L )
B - G A I N ( W H I T E L E V E L )
R - B I A S ( B L A C K L E V E L )
G - B I A S ( B L A C K L E V E L )
B - B I A S ( B L A C K L E V E L )
O S M H - P O S I T I O N
O S M V - P O S I T I O N
O S M D I S P L A Y T I M E
R G B DV
R - G A I N ( W H I T E L E V E L )
G - G A I N ( W H I T E L E V E L )
B - G A I N ( W H I T E L E V E L )
R - B I A S ( B L A C K L E V E L )
G - B I A S ( B L A C K L E V E L )
B - B I A S ( B L A C K L E V E L )
R G B DV
O S M H - P O S I T I O N
O S M V - P O S I T I O N
O S M D I S P L A Y T I M E
R G B DV
S O U R C E I N F O
V I D E O 1
N T S C 4 . 4 3
R G B DV R G B DV
S O U R C E I N F O
R G B 1
H - F R E Q
H - F R E Q
H - P O L
V - P O L
7 0 . 0 K H Z
7 0 . 0 H Z
N E G
N E G
DV Controls Group
The DV controls allow you to select an RGB2 signal format, to emphasize the
brightness of neutral tint, and to enhance the contrast by emphasizing black.
RGB2 SOURCE SELECT : Pressing + selects AUTO, RGB, YC B C R , YP B P R , or
RGB CTL in this order.
Normally selecting AUTO allows the monitor to
automatically distinguish between RGB and
component (YC B C R /YP B P R ) signals.
R G B 2 S O U R C E S E L E C T
G A M M A
D Y N A M I C P I C T U R E
1 2 3 4 5 A U T O
R G B 2 S O U R C E S E L E C T
G A M M A
D Y N A M I C P I C T U R E
1 2 3 4 OFF
R G B DV
R G B 2 S O U R C E S E L E C T
G A M M A
D Y N A M I C P I C T U R E
R G B DV
R G B DV