ROTEL RDV-1040 - Manual (Page 13)

13 English
To Resume Playback
When the resume mode is ON
While the disc that you interrupted playback
of is still on the disc tray, press
(PLAY)
28 . The RDV-1040 resumes playback from
the position where playback was interrupted.
The TV screen shows RESUME PLAY.
To play back from the beginning of the disc ■
(STOP) 9 before pressing (PLAY)
28 .
When the resume mode is DISC
RESUME
Press the OPN/CLS button on the front
panel or the OPEN/CLOSE button 2 on the
remote control to open the disc tray and in-
sert a disc for which the RDV-1040 has stored
an interrupted position. The TV screen shows
RESUME STOP.
Press (PLAY) 28 . The TV screen shows
RESUME PLAY and the RDV-1040 resumes
playback from the position where playback was
interrupted.
To play back from the beginning, after insert-
ing the disc, press
■ (STOP) 9 before
pressing (PLAY) 28 to start playback.
NOTES:
If you change the RESUME setting from
DISC RESUME to OFF or ON, you cannot
resume playback of a disc whose “resum-
ing” position is stored. However, when you
reset RESUME to DISC RESUME, you will
then be able to resume playback of the disc.
If you interrupt the playback of a disc for
which an interrupted position has already
been stored, the memory will be updated
with the new interrupted position.
For a double-sided DVD VIDEO disc, the
RDV-1040 regards each side as a different
disc. Therefore, to resume playback of such
a disc, the disc must be inserted with the
same side down.
When the RDV-1040 memorizes an inter-
rupted point for a disc, it also memorizes
Audio, Subtitle and Angle settings.
The RDV-1040 may not resume playback
exactly from the interrupted point. In the
case of an SVCD/Video CD disc with PBC
function, the RDV-1040 may resume play-
back from a point slightly earlier or later
than the point where playback was inter-
rupted.
Various Speed Playback
To Rapidly Advance or
Reverse Playback
During playback, press 29 or 10
on the remote control unit. You can select from
1.5 times, 5 times, 20 times and 60 times nor-
mal speed. Pressing
(PLAY) 28 returns
the RDV-1040 to normal playback.
During playback, hold down 8 or
26 . Playback is advanced or reversed at 5
times normal speed.
During rapid playback, the sound is muted ex-
cept when playing an Audio CD, and when
playing a DVD VIDEO or Video CD at 1.5 times
normal speed. For Audio CD discs, the sound
is heard intermittently.
1.5x Quick Playback With
Sound
When you select 1.5 times normal speed play-
back, the disc is played back with sound.
• For DVD VIDEO discs, the subtitles remain
on.
• If the sound of a DVD VIDEO disc is recorded
in Dolby Digital or DTS format, stereo lin-
ear PCM signals are output. With some DVD
VIDEO discs, the sound quality and volume
may be altered, or the sound may be out
of tune.
• To switch from rapid reverse playback to x1.5
Quick Playback, first press (PLAY)
28 , then press 29 once.
To Advance a Still Picture
Frame by Frame
With disc play paused, press I I (PAUSE)
27 . Each time you press II (PAUSE), the
still picture advances to the next frame. Press
(PLAY) 28 to return to normal play-
back.
To Play Disc in Slow Motion
You can select from 1/32 times, 1/16 times,
1/4 times and 1/2 times normal speed.
During playback, press II (PAUSE) 27 , then
press 29 (to play forward slow motion),
or 10 (to play reverse slow motion, for
DVD VIDEO disc only). Pressing (PLAY) 28
returns to normal playback.
• During slow motion playback, the sound will
be muted.
• Reverse slow motion playback is not pos-
sible for an SVCD and Video CD.
Locating the Beginning of a
Scene or Song
For DVD VIDEO: During playback, you can
skip a chapter or title, depending on the disc
configuration.
For SVCD/Video CD: During playback with-
out PBC function, you can skip a track –
For Audio CD: During playback or while in
stop mode, you can skip a track –
To skip forward, press 26 .
To skip backward, press 8 .