ROTEL RDV-1040 - Manual (Page 9)

9 English
Connecting the Power Cord
AC Input
Your RDV-1040 is configured at the factory for
the proper AC line voltage in the country where
you purchased it (USA: 115 volts/60Hz AC
or CE: 230 volts/50Hz AC). The AC line con-
figuration is noted on a decal on the back of
your unit.
After all the audio/video connections have been
made, plug the supplied power cord into the
AC INPUT receptacle on the back of the unit.
Then insert the power plug into an AC wall
outlet. The STANDBY indicator lights and setup
is complete. Note that a small amount of power
(3 watts) is always used while the power cord
is connected to the wall outlet.
Observe the following precautions:
• Do not connect or disconnect the power cord
with wet hands.
• Disconnect the power cord if you are not
going to use the unit for a long time.
• When unplugging the player from the wall
outlet, always pull the plug, not the power
cord.
• Disconnect the power cord before cleaning
the unit.
• Disconnect the power cord before moving
the unit.
• Do not damage, alter, twist or pull the power
cord. This may damage the cord and cause
fire, electric shock, or other accidents. Con-
tact your authorized Rotel dealer and get
a new power cord if the cord is damaged.
• Do not put anything heavy, on the unit, or
the power cord, as this may cause fire, elec-
tric shock, or other accidents.
RR-DV96 Remote Control
Installing the Batteries
The battery compartment is located on the back
of the remote control unit.
1 Press down on the
point shown by
the arrow at the
top of the com-
partment cover,
and pull up the
cover.
2 Place two R6P (SUM-3)/
AA(15F) batteries in the re-
mote control according to
the polarity markings (“+”
and “–”) inside the com-
partment and on the bat-
teries.
3 Place the cover
over the com-
partment, and
press down
lightly.
The batteries will last
about six months with normal use. If the func-
tions of the remote control become erratic, re-
place the batteries.
Precautions for the safe use of
batteries
Observe the following precautions for the safe
use of batteries. If they are used improperly
their life will be shortened, they may burst or
their contents may leak.
• Remove the batteries from the remote con-
trol if it will not be used for a long period
of time.
• Remove dead batteries and dispose of them
properly.
• Never leave dead batteries lying around.
Do not take them apart, mix them with other
refuse, or throw them into an incinerator.
• Never touch liquid that has leaked out of a
battery.
• Do not mix new and old batteries, or bat-
teries of different types, when replacing them.
Programming the RR-DV96
Remote to Control a TV
After it is programmed the RR-DV96 can op-
erate your TV set.
1 Set the TV/DVD switch 1 to TV.
2 Press and hold down the TV/VIDEO-CAN-
CEL
22 button. Then enter the manufac-
turer code of your TV listed in the following
table using the numeric buttons (0 - 9)
4 .
Do not release TV/VIDEO-CANCEL. button
until the next step is completed. (Example:
To enter code “01” press and release the
“0” button, then press and release the “1”
button.
3 Press the ENTER 34 button, then release
the TV/VIDEO-CANCEL button.
Manufacturer No.
Aiwa 36
Beijing 22
CCE 02
Changhong 34
Daewoo
17, 37
Ferguson 27
Finlux 30
Funai 32
Gradiente 15, 20
Grundig 19
Hitachi 10
ITT 28
Jinxing 38
JVC 01, 23,
24, 25
Konka 40
LG (Goldstar) 18
Magnavox
02
Mitsubishi 03
Mivar 29
Manufacturer No.
NEC 20
Noblex 22
Nokia 31
Panasonic 04, 11
Peony 34, 38,
39
Philco 10, 17,
21
Philips 02
RCA 05
Samsung 12, 33,
34, 35
Sanyo 13, 16
Sears 13
Sharp 06
Sony 07
TCL 41
Thomson 26
Toshiba 08, 14
Zenith 09
4 Test the program setting by pressing the TV
POWER
17 button to see if it turns your
set on. If there is more than one code listed
for the manufacturer of your TV, try them
one by one until you succeed.
Remote Control TV Operation
When the TV/DVD switch 1 is in the TV po-
sition the following buttons can be used to con-
trol the TV.
TV POWER 17
Turns the TV on or off.
CH+ and CH – 31 13
Changes the TV channels.
VOL+ and VOL – 32 12
Adjusts the TV volume.
TV/VIDEO button 22
Switches the TV input between TV and Video.
0 - 10 and (Numeric Buttons) 4
Selects the TV channels. Note: For some TVs,
pressing “+10” functions as the “+100”. The
“10” button functions as ENTER if your TV re-
quires pressing the ENTER after selecting a
channel number.
MUTING button 21
Mutes the TV sound.
External Remote In
The 3.5mm mini-jack (labeled EXT REM IN) re-
ceives command signals from an industry stan-
dard infrared receiver. This feature is useful
when the unit is installed in a cabinet and the
front panel sensor is blocked. Consult your au-
thorized Rotel dealer for information on ex-
ternal receivers and the proper wiring of a jack
to fit the mini-jack receptacle.