Russound UNO-TS2 - Manual (Page 15)

INSTALLER GUIDE
UNO-TS2 Overview
UNO-TS2 Overview for Installers
Note: The following minimum firmware revisions are required for use with the UNO-TS2:
CAV6.6 Rev. 3 2.01.16 or higher
CAV6.6 Rev. 4 3.01.10 or higher
CAM6.6 1.01.05 or higher
CAM Internal AM/FM Tuner 1.01.01 or higher
CAM Internal XM Module 2.00.05 or higher
ST2 Dual Tuner 3.00.10 or higher
ST2-XM (ST2 Chassis) 3.00.10 or higher
ST2-XM (XM Module) 2.00.05 or higher
SMS3 Media Server 2.00.07 or higher
15
The UNO-TS2 is an RNET-system enabled touch-
screen that functions similarly to the UNO-S2
keypad. It fits into a double-gang 32ci low volt-
age PVC junction box, uses a CAT-5 110 punch-
down connection, and supports one external IR
receiver. Active system status icons appear on
the screen (shared, master, party and do not dis-
turb). An “All On” or “All Off” can be performed
by pressing and holding the power button.
The CAV6.6 or CAM6.6 controller can NOT be
configured from the UNO-TS2. Controller configu-
ration must be performed using an UNO-S2 key-
pad or the PC Power Tool program.
For One UNO-TS2 per Controller
Note: 12V Zone triggers cannot be used
with this keypad configuration.
An RNET controller (CAV6.6, CAM6.6) supports
one UNO-TS2 and up to five UNO keypads per
controller, connected to the UNO System Keypad
Ports located on the back of the controller.
For 2 to 6 UNO-TS2s per Controller
(One UNO-TS2 per Zone)
Each UNO-TS2 must be connected to an SA-ZX3
Keypad Splitter. The SA-ZX3 is powered by a
1201A 1A power supply and uses an RJ-45
CAT-5 patch cable to connect to the controller’s
UNO Keypad Port. UNO-S1/S2 keypads can
share the SA-ZX3 with an UNO-TS2, but they
must be configured for the same zone.
After sources are configured in the RNET sys-
tem, they must be configured in the UNO-TS2
using a simple onscreen process under Installers
Setup. The configured source names (up to 6)
appear on the UNO-TS2 main screen, and unas-
signed source buttons remain blank. Custom
source names are set up in the optional PC
Power Tools program, and standard names are
set up with an UNO-S1 or UNO-S2 keypad.
The UNO-TS2 features pre-configured source
templates. Due to the unique screens used for
each source, the UNO-TS2 does not support the
key mapping features of the UNO-S1/S2 key-
pads. Custom key configuration (Key
Configuration menu of controller) is not recom-
mended and may result in unexpected behavior
by the UNO-TS2.
The UNO-TS2 screen blanker darkens the screen
when it has not been touched for a certain
amount of time. A touch to the screen brings the
screen back. This screen blank time can be
adjusted from 0 minutes (disables screen
blanker) to over an hour.
The UNO-TS2 may require future updates for
screens and for firmware. These updates are
performed in a similar fashion as UNO-S2
updates, with a programming cable and a PC.