Onkyo HT-R520 - Manual (Page 59)

59
Specifications
Amplifier Section
Video Section
Tuner Section
■ FM
■
AM
General
■
Video Inputs
■ Video Outputs
■
Audio Inputs
■
Audio Outputs
Specifications and features are subject to change without
notice.
Power output:
All channels:
130 W (8 Ω , 20 Hz–20 kHz, FTC)
Dynamic power: 2 x 260 W (3 Ω , front)
2 x 200 W (4 Ω , front)
2 x 95 W (8 Ω , front)
THD (total harmonic
distortion): 0.08% (rated power)
Damping factor: 60 (front, 1 kHz, 8 Ω )
Input sensitivity and
impedance: 200 mV/47 k Ω (LINE)
Output level and
impedance: 200 mV/470 Ω (REC OUT)
Frequency response: 10 Hz–100 kHz/+1 dB, –3 dB (Direct
mode)
Tone control: ±12 dB, 50 Hz (BASS)
±12 dB, 20,000 Hz (TREBLE)
S/N ratio (Direct mode): 100 dB (CD, IHF-A)
Speaker impedance:
6
Ω
~
Input sensitivity, output
level and impedance: 1.0 Vp-p/75 Ω (component and S-Video
Y)
0.7 Vp-p/75 Ω (component P B /C B , P R /C R )
0.28 Vp-p/75 Ω (S-Video C)
1.0 Vp-p/75 Ω (composite)
Component video
frequency response: 5 Hz–50 MHz
Tuning frequency range: 87.5–108.0 MHz
Usable sensitivity:
FM STEREO 17.2 dBf, 2.0 µV (75 Ω
IHF)
FM MONO 11.2 dBf, 1.0 µV (75 Ω IHF)
S/N ratio: FM STEREO 70 dB (IHF-A)
FM MONO 76 dB (IHF-A)
THD: FM STEREO 0.3% (1 kHz)
FM MONO 0.2% (1 kHz)
FM stereo separation: 45 dB at 1 kHz
Tuning frequency range: 530–1700 kHz
Usable sensitivity:
30 µV
S/N ratio: 40 dB
THD: 0.7%
Power supply: AC 120 V, 60 Hz
Power consumption: 4.6 A
Standby power
consumption: 2.5 W
Dimensions
(W x H x D):
17-1/8" x 5-7/8" x 14-13/16"
(435 x 150 x 376 mm)
Weight: 22.5 lbs. (10.2 kg)
Component video inputs:2 (DVD, Video 1/2/3)
S-Video inputs:
4 (DVD, Video 1–3)
Video inputs: 4 (DVD, Video 1–3)
Component video
outputs: 1 (Component Video Out)
S-Video outputs: 2 (Video 1 Out, Monitor Out)
Video outputs: 2 (Video 1 Out, Monitor Out)
Digital inputs: 4 (Optical 1–3, Coaxial)
Analog inputs: 6 (CD, Tape, DVD, Video 1–3)
Multichannel analog
inputs: 5.1 ch (Front L/R, Center, Surround L/R,
Subwoofer)
Analog outputs: 2 (Tape Out, Video 1 Out)
Subwoofer pre out: 1
Speaker outputs: 6+2
Phones: 1
• The HT-R520 contains a microcomputer for signal processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this
should happen, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.
That should fix it.
• To reset the HT-R520 to its factory defaults, turn it on and, while holding down the [VIDEO 1] button, press the
[STANDBY/ON] button. “Clear” will appear on the display and the HT-R520 will enter Standby mode.