Onkyo TX-SR803/803E - Manual (Page 84)

84
Zone 2 —Continued
Controlling Zone 2 with the Remote
Controller
Note:
• To control Zone 2, you must press the remote control-
ler’s [ZONE 2] REMOTE MODE button first.
Adjusting the Volume for Zone 2
To Mute Zone 2:
Press the remote controller’s [ZONE 2] button, followed
by the [MUTING] button. To unmute Zone 2, press the
remote controller’s [ZONE 2] button again, followed by
the [MUTING] button, or adjust the volume for Zone 2.
Notes:
• Only analog input sources are output by the ZONE 2
LINE OUT and ZONE 2 SPEAKERS terminals. Dig-
ital input sources are not output. If no sound is heard
when an input source is selected, check to see if it’s
connected to an analog input.
• When the ZONE 2 SPEAKERS terminals are used,
listening modes that require surround back speakers,
such as Dolby Digital EX, DTS-ES, and THX Select2
Cinema, are unavailable.
• While Zone 2 is on, the functions do not work.
• You can’t select different radio stations for the main
room and Zone 2. The same radio station will be used
for both.
1 Press the [ZONE 2] REMOTE
MODE button, then point the
remote controller at the AV
receiver and press the [ON] but-
ton.
Zone 2 turns on, and the ZONE 2 12V
TRIGGER OUT goes high (+12 V).
2 To select an input source for
Zone 2, press the [ZONE 2]
REMOTE MODE button, followed
by an INPUT SELECTOR button.
To select AM, FM, or XM, press the
[TUNER] INPUT SELECTOR button
repeatedly.
3 To turn off Zone 2, press the
[ZONE 2] REMOTE MODE button,
followed by the [STANDBY] but-
ton.
THX
10 - - / - - - 11 12
REMOTE MODE
HDD RECEIVER
TAPE/AMP
DVD CD
ZONE2
STEREO SURR
DIRECT
SUBTITLE AUDIO
ALLST
PLAY MODE
VIDEO OFF
REPEAT
OPEN/CLOSE
Re-EQ
+
-
T V CH
T V VOL
LISTENING MODE
INPUT SELECTOR
3 2
MACRO
1
+10 0 CLEAR
1 2 3
4 5 6
7 8 9
INPUT I
ON STANDBY
T V
CD
V1 V2 V3
MULTI CH DVD
TUNER
PHONO
V4
TAPE
PURE A
TEST TONE CH SEL LEVEL LEVEL
L NIGHT
RC-620M
ZONE2
ON
STANDBY
LEVEL–,
LEVEL+
INPUT
SELECTOR
ZONE2
ON
ZONE2
1 2 3
4 6
7 8 9
CD
V1
V4
V2 V3
DVD
TAPE TUNER
+10
PHONO
ZONE2
STANDBY
1 On the remote controller, press
the [ZONE 2] REMOTE MODE but-
ton, and then use the [LEVEL–]
and [LEVEL+] buttons.
On the AV receiver, use the ZONE
2 LEVEL [
]/[ ] buttons.
If your Zone 2 speakers are connected
to an amp in Zone 2, use its volume
control to adjust the volume.
OFF TONE ZONE 2
ZONE 2 LEVEL
PHONES STEREO DIMMER MEMORY
LISTENING MODE
TUNING MODE SETUP
PRESET PRESET TUNING
RETURN ENTER SETUP MIC
VIDEO S VIDEO DIGITAL
VIDEO 4 INPUT
AUDIO L R CLEAR
STANDBY/ON
STANDBY
MASTER VOLUME
PHONO
ZONE 2
DISPLAY PURE AUDIO TUNER TAPE VIDEO 4 VIDEO 3 VIDEO 2 VIDEO 1 DVD MULTI CH CD
OFF ON
POWER
ZONE 2 LEVEL ,
ZONE2
LEVEL LEVEL
ZONE 2 LEVEL
AV receiver