Troubleshooting —continued – Onkyo TXSR307 User Manual
Page 70
70
• Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
• If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not work
reliably when the doors are closed.
• Make sure you’ve selected the correct remote
controller mode (pages 11 and 64–66).
• Make sure you’ve entered the correct remote control
• Make sure to set the same ID on both the AV receiver
and remote controller (page 59).
Can’t control other components
• If it’s an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an
cable won’t work (page 31).
• Make sure you’ve selected the correct remote
controller mode.
• If you’ve connected an
-capable Onkyo MD
recorder, CD recorder, or RI Dock to the TV/TAPE
IN/OUT jacks, or an RI Dock to the CBL/SAT IN or
VCR/DVR IN jacks, for the remote controller to work
properly, you must set the Input Display to “MD”,
“CDR”, or “DOCK”, respectively (page 37).
• The entered remote control code may not be correct. If
more than one code is listed, try each one.
• With some AV components, certain buttons may not
work as expected, and some may not work at all.
• To control an Onkyo component that’s connected via
, point the remote controller at the AV receiver. Be
sure to enter the appropriate remote control code first
(page 63).
Can’t record
• On your recorder, make sure the correct input is
selected.
• To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (e.g., TV/TAPE IN to TV/TAPE
OUT or VCR/DVR IN to VCR/DVR OUT).
The sound changes when I connect my
headphones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono or Direct in which case it stays the same.
How do I change the language of a multiplex
source
• On the “7. Audio Adjust” menu, change the “Input
(Mux)” setting to “Main” or “Sub” (page 57).
The
functions don’t work
• To use
, you must make an
connection and an
analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally (page 31).
When performing “Audyssey 2EQ™ Room
Correction and Speaker Setup”, the
measurement fails showing the message
“Ambient noise is too high”.
• This can be caused by any malfunction in your speaker
unit. Check if the unit produces normal sounds.
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these
settings.
1. While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
2. Use the Left and Right [
]/[
] buttons to change
the setting.
3. Press the [SETUP] button when you’ve finished.
• Video Attenuation
This setting can be made for the DVD/BD,
VCR/DVR, CBL/SAT, or AUX input.
If you have a games console connected to the
composite video input, and the picture isn’t very
clear, you can attenuate the gain.
Video ATT:0: (default).
Video ATT:2: Gain is reduced by 2 dB.
Recording
Others
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or static
electricity may cause it to lockup. In the unlikely event that
this happens, unplug the power cord from the wall outlet,
wait at least 5 seconds, and then plug it back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
this unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to Standby.