Onkyo Network TX-8050 - Manual (Page 41)

En-
41
Advanced Setup —Continued
1. Digital Audio Input
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example,
if you connect your CD player to the OPTICAL IN 1,
you must assign “OPTICAL1” to the “CD” input
selector.
Here are the default assignments.
COAXIAL1, COAXIAL2, OPTICAL1, OPTICAL2:
Select the corresponding digital audio input, to which
the component has been connected.
–––––:
Select if the component is connected to an analog audio
input.
Notes:
• Available sampling rate for PCM signals from a
digital input (optical and coaxial) is 32/44.1/48/88.2/
96 kHz/16, 20, 24 bit.
• If you connect a component (such as a UP-A1 Dock
with an iPod inserted) to the UNIVERSAL PORT
jack, you cannot assign any input to the PORT
selector.
2. Source Setup
Intelli Volume
See page 40.
IntelliVolume does not apply for Zone 2.
Name
This changes the name displayed by the INPUT selector.
First use the INPUT selector to select the name of the
source you want to change, and then use this Setup Menu
to change the name that's displayed. Use the []/[]
buttons to step through the following names.
– – –  Blu-ray  DVD  HD DVD  VCR  DVR
 Tivo  CableSTB  SAT STB  PS3  Wii 
Xbox  PC  TV  CD  TAPE  iPod  – – –
Name Edit
You can edit the name of the radio preset if an FM or AM
preset station is being received. (See page 25)
3. Hardware Setup
Speaker Impedance
See “Configuring the Speaker Impedance” on page 12.
AM/FM Frequency Setup (North American model)
For AM/FM tuning to work properly, you must specify
the AM/FM frequency step (10 kHz/200 kHz or 9 kHz/
50 kHz) used in your area. Note that when this setting is
changed, all radio presets will be deleted.
Default setting: 10 kHz/200 kHz
AM Frequency Setup (European model)
For AM tuning to work properly, you must specify the
AM frequency step (9 kHz/10 kHz) used in your area.
Note that when this setting is changed, all radio presets
will be deleted.
Default setting: 9 kHz
Auto Standby
When “Auto Standby” is set to “On”, the receiver will
automatically enter Standby mode if there is no
operation for 30 minutes with no audio and no video
signal input.
Default setting: Off (North American model),
On (European model)
Notes:
• With some sources, the Auto Standby function may
activate itself during playback.
• The Auto Standby function does not work when
Zone2 is on.
UP-A1 Charge Mode
You can specify how the power is fed to your iPod/
iPhone when the receiver is in Standby Mode.
Auto: Power feeding is interrupted when your iPod/
iPhone is fully charged.
On: Power feeding continues even if your iPod/iPhone is
fully charged.
Off: Your iPod/iPhone is not charged.
Default setting: Auto
Notes:
• This cannot be selected if no device is connected to
UNIVERSAL PORT.
• This setting cannot be selected when:
– the UP-A1 Dock with docked iPod/iPhone is not
connected to the receiver, or
– the docked iPod/iPhone model is not supported.
• When the “UP-A1 Charge Mode” setting is set to
“On”, or to “Auto” with your iPod/iPhone recharging,
the SLEEP indicator is dimly lit in standby mode. In
such conditions, the power consumption of the
receiver slightly increases.
Advanced Setup Menu
Input selector Default assignment
BD/DVD COAXIAL 1
VCR/DVR –––––
CBL/SAT COAXIAL 2
GAME OPTICAL 1
TV/TAPE –––––
CD OPTICAL 2
PHONO –––––
PORT –––––