Onkyo HT-RC370 User Manual
Page 32
32
En
Note
• You can cancel Audyssey MultEQ XT Room Correction and
Speaker Setup at any point in this procedure simply by
disconnecting the setup microphone.
• Do not connect or disconnect any speakers during
Audyssey MultEQ XT Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ XT Room Correction and Speaker
Setup starts.
• Changes to the room after Audyssey MultEQ XT Room
Correction and Speaker Setup requires you run
Audyssey MultEQ XT Room Correction and Speaker Setup
again, as room EQ characteristics may have changed.
3
When you’ve finished making the settings, press
ENTER.
Perform the “Speaker Setup” according to your
speaker configuration:
– Speakers Type(Front) (
– Powered Zone 2 (
– Subwoofer (
If you use a powered subwoofer(s), go to step 4. If
not, go to step 5.
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
optional unit setting may appear on the speaker
setting menu.
4
Adjust the subwoofer volume level to 75 dB.
Test tones are played through the subwoofer. Use the
volume control on the subwoofer.
Note
• If your subwoofer does not have a volume control,
disregard the level displayed and press ENTER to proceed
to the next step.
• If you set the subwoofer’s volume control to its maximum
and the level displayed is lower than 75 dB, leave the
subwoofer’s volume control at its maximum and press
ENTER to proceed to the next step.
5
Use / to select “Audyssey Quick Start” or
“Audyssey MultEQ XT Full Calibration”.
6
Press
ENTER.
Audyssey MultEQ
®
XT Room Correction and
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ XT Room Correction and Speaker
Setup runs. This process takes a few minutes. Please
refrain from talking during measurements and do
not stand between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ XT Room Correction and
Speaker Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to
step 9.
7
Place the setup microphone at the next position,
and then press
ENTER.
Audyssey MultEQ XT performs more measurements.
This takes a few minutes.
8
When prompted, repeat step 7.
MultEQ XT: Auto Setup
AUDYSSEY
Speakers Type(Front)
Normal
Powered Zone 2
No
Subwoofer Yes
9
Use / to select an option, and then press
ENTER.
The options are:
`
Save:
Save the calculated settings and exit
Audyssey MultEQ XT
Room Correction and
Speaker Setup
.
`
Cancel:
Cancel Audyssey MultEQ XT
Room Correction
and Speaker Setup
.
Note
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using
/
.
10
Use / to select a target, and use
/
to change
the setting.
After the results of Audyssey MultEQ XT have been
saved, the menu will display the “Audyssey”
(
page 51),
Note
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• These settings are applied to all input selectors.
11
Press
ENTER.
12
Disconnect the speaker setup microphone.
Subwoofer :
Yes
Front :
100Hz
Center :
40Hz
Surround :
100Hz
Front Wide
:
None
Front High
:
None
Surround Back
:
120Hz
Surround Back Ch
:
2ch
Save
Cancel
MultEQ XT: Auto Setup
AUDYSSEY
-- Review Speaker Configuration --