Onkyo HT-RC370 - Manual (Page 45)

45
En
Note
• If no video component is connected to HDMI output (even if the
HDMI input is assigned), the AV receiver selects the video
source based on the setting of “Component Video Input”.
• When an HDMI IN is assigned to an input selector as explained
here, the same HDMI IN will be set as a priority in the “Digital
Audio Input” (
➔
page 45). In this case, if you want to use the
coaxial or optical audio input, make the appropriate selection in
the “Audio Selector” setting (
➔
page 55).
• The “TUNER” selector cannot be assigned and is fixed to the
“- - - - -” option.
• “AUX” is used only for input from the front panel.
• Do not assign an HDMI IN to the TV/CD selector while “HDMI
Control(RIHD)” is set to “On” (
➔ page 57), otherwise
appropriate CEC (Consumer Electronics Control) operation will
not be guaranteed.
• If you assign “- - - - -” to an input selector that is currently
selected in “HDMI Through” ( ➔ page 58), the “HDMI
Through” setting will be automatically switched to “Off”.
• If you connect a component (such as UP-A1 Dock with docked
iPod/iPhone) to the UNIVERSAL PORT jack, you cannot
assign any input to the “PORT” selector.
Component Video Input
If you connect a video component to a component video
input, you must assign that input to an input selector. For
example, if you connect your Blu-ray Disc/DVD player to
COMPONENT VIDEO IN 2, you must assign “IN2” to
the “BD/DVD” input selector.
Here are the default assignments.
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,
TV/CD, PHONO, PORT
` IN1, IN2:
Select a corresponding component video input to
which the video component has been connected.
`
- - - - -:
Output composite video and S-Video sources from
the HDMI output.
Note
• If you connect a component (such as UP-A1 Dock with docked
iPod/iPhone) to the UNIVERSAL PORT jack, you cannot
assign any input to the “PORT” selector.
• The “AUX” selector is fixed to the “- - - - -” option.
• The “TUNER” selector cannot be assigned and is fixed to the
“- - - - -” option.
Digital Audio Input
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign “OPTICAL1” to the “TV/CD” input
selector.
Here are the default assignments.
■
BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,
TV/CD, PHONO, PORT
`
COAXIAL1, COAXIAL2, COAXIAL3,
OPTICAL1, OPTICAL2:
Select a corresponding digital audio input to which
the component has been connected.
`
- - - - -:
Select if the component is connected to an analog
audio input.
Note
• When an HDMI IN is assigned to an input selector in “HDMI
Input” ( ➔ page 44), the same HDMI IN will be set as a priority
in this assignment. In this case, if you want to use the coaxial or
optical audio input, make the selection in the “Audio Selector”
(
➔
page 55).
• Available sampling rates for PCM signals from a digital input
(optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
• If you connect a component (such as UP-A1 Dock with docked
iPod/iPhone) to the UNIVERSAL PORT jack, you cannot
assign any input to the “PORT” selector.
• The “AUX” selector is fixed to the “- - - - -” option.
• The “TUNER” selector cannot be assigned and is fixed to the
“- - - - -” option.
Analog Audio Input
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s
subwoofer sensitivity to match your DVD player.
■
Subwoofer Input Sensitivity
`
0dB to 15dB in 5 dB steps.
Note
• This setting only affects signals connected to the AV receiver’s
multichannel input subwoofer jack.
• If you find that your subwoofer is too loud, try the 10 dB or
15 dB setting.
Input selector Default assignment
BD/DVD IN1
VCR/DVR - - - - -
CBL/SAT IN2
GAME - - - - -
PC - - - - -
TV/CD - - - - -
PHONO - - - - -
PORT - - - - -
Input selector Default assignment
BD/DVD COAXIAL1
VCR/DVR COAXIAL2
CBL/SAT COAXIAL3
GAME OPTICAL1
PC - - - - -
TV/CD OPTICAL2
PHONO - - - - -
PORT - - - - -