Onkyo HT-RC370 - Manual (Page 61)

61
En
Audyssey
■
Audyssey
See “Audyssey” in “Source Setup” (
➔ page 51).
■
Dynamic EQ
See “Dynamic EQ” in “Source Setup” (
➔
page 51).
■ Dynamic Volume
See “Dynamic Volume” in “Source Setup” (
➔
page 52).
Note
• These technologies can be used when all the following
conditions are met:
– Room Correction and Speaker Setup is completed. Note that
“Audyssey” requires the “Audyssey MultEQ XT Full
Calibration” method.
– Any listening mode other than Direct or Pure Audio is
selected.
– A pair of headphones is not connected.
– multichannel analog input is not selected.
• The setting is stored individually for each input selector.
• “Dynamic EQ” and “Dynamic Volume” cannot be selected
when any of the THX listening modes is selected, with
“Loudness Plus” set to “On” or “Preserve THX Settings” set
to “Yes”.
• When “Dynamic EQ” is set to “On” or “Dynamic Volume” is
set to anything else than “Off”, “Dolby Volume” will be
switched to “Off”.
Late Night
■
Late Night
For Dolby Digital and Dolby Digital Plus sources, the
options are:
`
Off
` Low:
Small reduction in dynamic range.
`
High:
Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
`
Auto:
The Late Night function is set to “On” or “Off”
automatically.
`
Off
`
On
Turn this setting on to reduce the dynamic range of Dolby
Digital material so that you can still hear quiet parts even
when listening at low volume levels—ideal for watching
movies late at night when you don’t want to disturb
anyone.
Note
• The effect of the Late Night function depends on the material
that you are playing and the intention of the original sound
designer, and with some material there will be little or no effect
when you select the different options.
• The Late Night function can be used only when the input source
is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.
• The Late Night function is set to “Off” when the AV receiver is
set to standby. For Dolby TrueHD sources, it will be set to
“Auto”.
Music Optimizer
■
Music Optimizer
`
Off
`
On
Turn this setting on to enhance the sound quality of
compressed music files. Use it with music files that use
“lossy” compression, such as MP3.
Note
• The Music Optimizer function only works with PCM digital
audio input signals with a sampling rate below 48 kHz and
analog audio input signals. The Music Optimizer is disabled
when the Direct or Pure Audio listening mode is selected.
• The setting is stored individually for each input selector.
• The M.Opt indicator will light (
➔ page 9).
• This setting is not available when the multichannel Analog input
is selected.
Re-EQ
With the Re-EQ function, you can compensate a
soundtrack whose high-frequency content is too harsh,
making it more suitable for home theater viewing.
■
Re-EQ
`
Off
`
On
This function can be used with the following listening
modes: Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, Multichannel, DTS, DTS-HD High
Resolution Audio, DTS-HD Master Audio, DTS Express,
DSD, Dolby EX, Dolby Pro Logic IIz Height, Dolby
PLIIx Movie, Neo:6 Cinema and 5.1-channel source +
Neo:6.
■ Re-EQ(THX)
`
Off
`
On
This function can be used with the following listening
modes: THX Cinema, THX Surround EX, and
THX Select2 Cinema.
Note
• Settings for the Re-EQ function are kept in each listening mode.
In THX listening mode however, the setting will return to “On”
when the AV receiver is turned off.