Onkyo DV-SP506 - Manual (Page 51)

51
Configuring the DV-SP506 —Continued
SCART Output Setting
(European model only)
With this setting you can select the video format to be
used for the SCART AV CONNECTOR: RGB, S-Video,
or composite video. Before changing this setting, refer to
your TV’s manual to see if its SCART input can accept
video signals in these formats.
Composite (default): Composite video offers stan-
dard quality.
S-Video: S-Video offers the next best picture quality.
RGB: This format offers the best picture quality.
Notes:
• If you select a format that is not supported by your TV,
the setup menu may disappear from the screen. If this
happens, switch off your equipment, connect the
DV-SP506 to your TV with a composite video or
S-Video cable, and then change this setting.
• When RGB is selected, nothing is output by the com-
ponent video output.
Depending on the HDMI Audio Out setting (see below),
Audio menu settings may be fixed at a particular value,
available for changing, or unavailable, as shown in the
following table.
✓
: Available
✗
: Unavailable
*1: Set automatically depending on the connected HDMI com-
ponent.
*2: When the Subwoofer setting is set to Off, this setting is
fixed at Large.
*3: If the Front Speaker, Surround Speaker, or Center Speaker
setting is set to Small, this setting can only be set to Small
or Off.
*4: When the DV-SP506 is set to Standby, this setting is auto-
matically set to Off.
HDMI Audio Out
With this setting you can specify how the HDMI OUT
outputs audio.
Auto (default): Audio is output at optimum quality.
6ch DSD: SACD audio is output in DSD (Direct
Stream Digital) format. If the HDMI input on your
AV receiver or TV does not support DSD, there will
be no sound. This option is also suitable for SACD
playback via the multichannel analog audio output.
6ch PCM: SACD audio is converted to 6-channel
PCM with a sampling rate of 176.4 kHz. If the
HDMI input on your AV receiver or TV does not
support 6-channel PCM, there will be no sound. This
option is also suitable for playback of 6-channel
PCM on a DVD-Audio disc.
2ch PCM: Multichannel audio is converted to 2-
channel PCM. Select this option to output the sound
through your TV’s speakers without using an AV
receiver. Dolby Digital and DTS will be converted to
PCM.
Off: Audio is not output by the HDMI OUT. Audio is
output by the OPTICAL and COAXIAL digital out-
puts. Select this option if you’re using the analog or
digital audio outputs to output audio instead of the
HDMI OUT.
Note:
• While an SACD or DVD-Audio disc is loaded, this
setting cannot be changed. Eject the disc first if you
need to change this setting.
Digital Audio Out
With this setting you can configure the type of audio sig-
nals output from the digital audio outputs. If your TV or
AV receiver does not support Dolby Digital or DTS,
select the PCM option.
All (default): Dolby Digital and DTS signals are out-
put as they are.
PCM: Dolby Digital and DTS signals are converted
to Linear PCM. If your TV or AV receiver does not
support Dolby Digital or DTS, select the PCM
option.
Off: No digital signals are output by the digital out-
puts.
Note:
• MPEG is output as PCM regardless of this setting.
Audio Menu
Setting
HDMI Audio Out setting
Auto
6ch
DSD
6ch
PCM
2ch
PCM
Off
Digital Audio Out *1 *1 *1 PCM
✓
Linear PCM Out *1 *1 *1 On
✓
Subwoofer On On On
✓ ✓
Front Speaker Large Large Large
✓ ✓ *2
Center Speaker Large Large Large
✓ ✓ *3
Surround Speaker Large Large Large
✓ ✓ *3
Center Delay Off Off Off
✓ ✓
Surr. Delay Off Off Off
✓ ✓
Test Tone Off Off Off
✓ ✓
Dynamic Range
Control
Off Off Off
✓ *4 ✓ *4
Dolby Pro Logic Off Off Off
✓ ✓
SACD Audio
Setup
*1 DSD PCM PCM
✓
Downmix Setting
✗ ✗ ✗ ✓ ✓