Thermador KBUIT4250A - Manual (Page 19)

19
To install anti-tip boards
1. Mark the stud locations on rear wall 80 in. to 90 in. (203 -
229 cm) above floor.
2. Securely attach one or two 2 in. x 4 in. x 32 in.
(5 cm x 10 cm x 81 cm) wood boards to wall studs behind
refrigerator. Use 6 - #8 x 3 in. (7.6 mm) (or longer) wood
screws. The wood screws must be screwed into the studs at
least 1½ in. (3.8 cm). The board(s) must overlap the
compressor cover.
C o n n e c t Wa t e r S u p p l y
1. Remove the shipping tape from the gray, coiled water tubing
on the rear of the refrigerator.
2. Before attaching copper tubing to the refrigerator, flush at
least 2 qt. (1.9 L) of water through the copper tubing and into
a bucket to get rid of any particles in the water line.
3. Check for leaks around the saddle valve. Do not overtighten
the clamp or sleeve. This will crush the copper tubing.
4. Make connection to the refrigerator.
Style 1 - Connecting to a Water Valve:
NOTE: The water shutoff valve should be located in the base
cabinet on either side of the refrigerator. The right-hand side
is recommended. The access hole through the right cabinet
must be within
¹⁄₂ in. (12.7 mm) of rear wall.
Push the bulb end of the tubing into the water valve as far as
it will go. Slide the nut forward and finger tighten. Then
tighten it with a wrench two more turns. Do not overtighten.
Style 2 - Connecting to a Water Line
Additional Parts Needed: Coupling, ferrule and nut.
Slide the purchased nut then the purchased ferrule onto the
tubing. Push the tubing into the purchased coupling as far as
it will go. Slide the nut and ferrule forward. Tighten the nut by
hand. Then tighten it with a wrench two more turns. Do not
overtighten.
5. Turn shutoff valve ON.
6. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
P l u g i n R e f r i g e ra t o r
1. Set control switch at top of cabinet to the OFF position.
2. Plug into a grounded 3 prong outlet.
M ove R e f r i g e ra t o r t o F i n a l
Po s i t i o n
IMPORTANT: To prevent floor damage, make sure levelers are
raised (not touching floor) and refrigerator is on rollers before
moving.
1. Place top of cardboard carton or plywood under refrigerator.
Remove dolly.
2. Do not remove protective film.
3. Move the refrigerator straight back and evenly into the
opening. Check to make sure that water tubing is not kinked
and the power supply cord is on top of the refrigerator next to
the cover.
1. Center board ¹⁄₄ in. (6.35 mm) max. above refrigerator
2. Two 2 in. x 4 in. x 32 in. (5 cm x 10 cm x 81 cm) boards
3. Attach to studs with 6 -#8 x 3 in. (7.6 cm) screws
4. Compressor cover
1. Bulb
2. Nut (provided)
2 1
3
2" (5 cm)
4
1
2
1. Line to refrigerator
2. Nut (provided)
3. Bulb 4. Coupling (purchased)
5. Ferrule (purchased)
6. Nut (purchased)
1 2 3 4 5 6
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Do not use an extension cord.
Do not use an adapter.
Do not remove ground prong.