Waterford Appliances NATURAL GAS E61-LP - Manual (Page 17)

17 Waterford E61 Gas Fireplace Insert
FAN MAINTENANCE
If your fan requires maintenance or replace-
ment, access to the fan is through the plate on
the rear wall of the firebox. NOTE: the unit
MUST NOT be operated without the fan
access panel securely in place and cor-
rectly sealed.
IMPORTANT: These fans collect a
lot of dust from within your home.
Ensure you maintain these fan mo-
tors on a regular basis by vacuum-
ing out the fan squirrel cages, around
the motor, and around the grills on
the back of the stove.
Remove the 7 nuts holding the
Front Glass Bracket to the front face.
CAUTION: Don't let the glass drop.
Top View of pilot flame
Top View of pilot flame
Incorrect flame pattern will have small, probably
yellow flames, not coming into proper contact
with the rear of the burner or thermopile.
LOG REPLACEMENT &
CLEANING
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door to carefully remove the
logs. The pilot light generates enough heat to
burn someone. If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs must
be as shown in the diagram under Log Installa-
tion.
NOTE: Improper positioning of
logs may create carbon build-up
and will alter the unit’s perform-
ance which is not covered under
warranty.
Cleaning the Log Set and Firebox
During the annual inspection and maintenance
appointment, the service person should clean
dust, lint, and any light accumulation from the
logs and firebox area. An extra-soft brush
should be use don the logs as they are extreme-
ly fragile; a vacuum cleaner may be used on the
firebox. See the log installation instructions for
details on removing and replacing the logs.
DOOR AND GLASS
GASKET
If the door gasket requires replacement use only
the proper replacement gasket available from
your Waterford dealer.
GLASS REPLACEMENT
Your Waterford stove is supplied with high
temperature, 5 mm Neoceram ceramic glass
that will withstand the highest heat that your unit
will produce. In the event that you break your
glass by impact, purchase your replacement
from an authorized Waterford dealer only, and
follow our step-by-step instructions for re-
placement.
1) Remove the door by lifting it slightly up and
off the front face.
MAINTENANCE
WARNING: CHILDREN AND
ADULTS SHOULD BE ALERTED
TO THE HAZARDS OF HIGH SUR-
FACE TEMPERATURE AND
SHOULD STAY AWAY TO AVOID
BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME ROOM AS
THE APPLIANCE.
CLOTHING OR OTHER FLAMMA-
BLE MATERIAL SHOULD NOT BE
PLACED ON OR NEAR THE APPLI-
ANCE.
7) Each time the appliance is lit, it may cause
condensation and fog the glass. This con-
densation and fog is normal and will disap-
pear in a few minutes as the glass heats up.
Never operate the appliance without
the glass properly secured in place or
with the door open.
8) Periodically check the pilot flames. Correct
flame pattern has three strong blue flames:
1 flowing around the thermopile and 1
around the thermocouple, and 1 flowing
across the rear of the burner (it does not
have to be touching the burner).
Note: If you have an incorrect flame pat-
tern, contact your Waterford deal-
er for further instructions.
2) a) Remove the 7 nuts that secure the front
glass bracket holding the center glass
in place.
b) If removing the side glass, remove the
2 nuts that secure the retainers holding
each side glass in place.
3) Remove the glass and replace with the new
glass.
4) Install the front glass bracket and turn the
nuts just enough to support the glass. Tight-
en the nuts alternately. Avoid overtighten-
ing the nuts as this may damage the glass.