Wayne-Dalton 8850 - Manual (Page 12)

12
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
Tools Needed:
Tools Needed:
12
Tools Needed:
Tools Needed:
7
Top bracket
Power Drill
7/16” Socket
Driver
Align upper-center hole of top bracket
with vertical groove on the end stile and
ensure top bracket is level and aligned
with edge of top section. Secure with
(4) 1/4”- 20 x 7/8” self drilling screws,
one in each corner of the top bracket, as
shown . Loosely fasten top bracket slide
with (1) 5/16” - 18 x 3/4” carriage bolt
and 5/16” - 18 hex nut. Insert roller into
slide. Repeat for other side.
If your door has double end stiles then it
will require 4 top brackets; as shown, in
which case an additional top bracket will
be installed in the same manner next to
the first top bracket with one roller being
placed through both top bracket slides.
four reinforcement brackets will then be
installed under the 4 top brackets and
secured to the section with (4) 1/4”- 20 X
7/8” self drilling screws.
NoTe: If your door is trolley operated; it
is recommended that an optional strut be
installed on the top rail.
Now stack the top section. Take care to
ensure it is aligned properly with the other
sections.
(4) 1/4”- 20 X 7/8”
SELf DRILLING
SCREWS
TOP BRACKET
BASE
END STILE
TOP SECTION
8
lift handle
bottom section
Locate the center most stile of the bottom section of the door.
On the inside of the door, center the lift handle vertically with
the center stile; horizontally on the bottom section rail, and
within 8” of the bottom of the section.
Use the lift handle as a template, place a mark at each hole
location onto the bottom section rail. Drill a 9/32” diameter
hole through the section at each marked location.
NoTe: Be extremely careful to keep drill straight.
Assemble the outside and inside lift handle to the section
using (4) 1/4” -20 x 5/8” self drilling screws.
lock (2nd) section
Position the lift handle’s bottom hole 4” from the bottom of
the lock (2nd) section. Vertically align with the lift handle on
the bottom section. Using the lift handle as a template, place
mark at each hole location onto the center stile. Drill a 9/32”
diameter through the section at each marked location.
NoTe: Be extremely careful to keep drill straight.
Assemble the outside and inside lift handle to the section
using (4) 1/4” -20 x 5/8” self drilling screws.
TO AVOID POSSIBLE INjURY, LIfT hANDLES ThAT ARE
INSTALLED WIThIN 4 INChES Of A SECTION INTERfACE
ShALL PROMOTE VERTICAL ORIENTATION Of ThE hAND.
LIfT hANDLE OUTSIDE
LIfT hANDLE INSIDE
Tape Measure
Pencil
Power Drill
9/32” Drill Bit
1/4” Wrench
LOCK
SECTION
LOCK
SECTION
LOCK
SECTION
LOCK
SECTION
BOTTOM
SECTION
BOTTOM
SECTION
BOTTOM
SECTION BOTTOM SECTION
LIfT
hANDLE
LIfT
hANDLE
LIfT
hANDLE
LIfT
hANDLE
(2) 1/4” - 20
X 5/8” SELf
DRILLING
SCREWS
(2) 1/4” - 20
X 5/8” SELf
DRILLING SCREWS
waRNiNg
TOP SECTION
TOP
BRACKET
BASE
5/16” - 18
hEX NUT
(1) 5/16” - 18 X 3/4”
CARRIAGE BOLT
TOP
BRACKET
SLIDE
TOP SECTION
(16) 1/4”- 20 X 7/8”
SELf DRILLING
SCREWS
(4) 1/4”- 20 X 7/8”
SELf DRILLING
SCREWS
(4) REINfORCEMENT
BRACKETS