Zoom G1U - Manual (Page 14)

26 ZOOM G1u
Effect Types and Parameters
27 ZOOM G1u
Checking the G1u Version
A 1 A 9
Analog Delay
This effect simulates an analog delay with a long delay time of up to 5000 msec. The right-digit setting
values control the mixing ratio of the effect sound and the feedback amount.
P 1 P 9
Ping Pong Delay
This is a ping-pong type delay where the delay sound alternates between left and right. The right-digit setting
values control the mixing ratio of the effect sound and the feedback amount.
R 1 R 9
Reverse
This is a special delay where the effect sounds as if playing in reverse. Maximum delay time is 2500 msec.
Higher settings result in stronger effect sound.
TIME (Prm2)
Controls parameter 2 of the DELAY module. The setting range is different for the
Reverse effect type and other effect types.
When Delay – Ping Pong Delay is selected
1 5 0
Time (Delay Time)
Sets the delay time. In the 10 – 1000 millisecond range, the adjustment is performed in 10-msec steps
(1 – 99, 1.0). Above 1 second, the adjustment is performed in 100-msec steps (1.1 – 5.0).
When Reverse is selected
0 1 2 5
Time (Delay Time)
Sets the delay time. In the 10 – 1000 millisecond range, the adjustment is performed in 10-msec steps
(10 – 99, 1.0). Above 1 second, the adjustment is performed in 100-msec steps (1.1 – 2.5).
n REVERB module
REVERB (Type&Prm1)
Selects the REVERB module effect type and controls parameter 1 at the same time.
H 1 H 9
Hall
This reverb effect simulates the acoustics of a concert hall. Higher right-digit settings increase the mixing
ratio of the effect sound.
R 1 R 9
Room
This reverb effect simulates the acoustics of a room. Higher right-digit settings increase the mixing ratio of
the effect sound.
S 1 S 9
Spring
This effect simulates a spring-type reverb. Higher right-digit settings increase the mixing ratio of the effect
sound.
A 1 A 9
Arena
This reverb effect simulates the acoustics of a large venue such as a sports arena. Higher right-digit settings
increase the mixing ratio of the effect sound.
T 1 T 9
Tiled Room
This reverb effect simulates the acoustics of a tiled room. Higher right-digit settings increase the mixing ratio
of the effect sound.
DECAY (Prm2)
Controls parameter 2 of the REVERB module. This parameter is common to all effect
types.
1 3 0
Decay
Adjusts the decay duration.
Troubleshooting
• No power
Refer to "Turn power on" on page 6.
• Reverb effect does not operate
While a rhythm pattern is playing, the reverb
effect is not available. Stop the rhythm pattern
first (g p. 10).
• Delay effect does not operate
While the looping function is being used, the
delay effect is not available. Stop the looping
function first (g p. 12).
• Patch switching does not change the
sound
Is the patch selection method of the G1u set to
"pre-select" (g p. 18)? Turn power off and then
on again to return to normal operation.
• High level of noise
Is ZOOM AC adapter being used? Be sure to use
only an adapter for 9 V DC, 300 mA with center
minus plug (ZOOM AD-0006).
• Battery life is short
Are manganese batteries being used? Continuous
operation time is about 10 hours with alkaline
batteries.
Rhythm Function Preset Patterns
# Name TimSig # Name TimSig # Name TimSig # Name TimSig
1 8beat 1 4/4 11 METAL 2 4/4 21 POP 3 4/4 31 BALLAD 1 4/4
2 8beat 2 4/4 12 THRASH 4/4 22 DANCE 1 4/4 32 BALLAD 2 3/4
3 8beat 3 4/4 13 PUNK 4/4 23 DANCE 2 4/4 33 BLUES 1 4/4
4 8shuffle 4/4 14 DnB 4/4 24 DANCE 3 4/4 34 BLUES 2 3/4
5 16beat 1 4/4 15 FUNK 1 4/4 25 DANCE 4 4/4 35 JAZZ 1 4/4
6 16beat 2 4/4 16 FUNK 2 4/4 26 3per4 3/4 36 JAZZ 2 3/4
7 16shuffle 4/4 17 HIPHOP 4/4 27 6per8 3/4 37 METRO 3 3/4
8 ROCK 4/4 18 R'nR 4/4 28 5per4 1 5/4 38 METRO 4 4/4
9 HARD 4/4 19 POP 1 4/4 29 5per4 2 5/4 39 METRO 5 5/4
10 METAL 1 4/4 20 POP 2 4/4 30 LATIN 4/4 40 METRO
Checking the G1u Version
Checking the G1u Software Version, perform the following steps.
1. Turn power to the G1u on while
holding down the [BANK UP·TAP] key
and the [
Q
] foot switch.
The higher two digits of the current version are
shown on the display.
2. Press the [
Q
] foot switch.
The l ower two digits of the current version are
shown on the display.
3. Pressing either of the [
W
]/[
Q
] foot
switches causes the version display
to go off, and the G1u restarts.
Detailed information about the latest software
version can be found on the ZOOM web site:
http://www.zoom.co.jp/