Yamaha DSP-AZ1 - Manual (Page 23)

E-
21
PREP
ARA
TIONS
English
CONNECTIONS
Connecting video components
Before you connect any components, disconnect the power supply to all the components you plan to connect including this unit and deter-
mine which jacks are for the left and right channels and for input and output. After you finish all connections, check them again to make sure
they are correct.
■ About the video jacks
There are three types of video jacks.
AC OUTLETS
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAINS
SWITCHED
SPEAKERS
R L FRONT
R
R L
L REAR
CENTER
MAIN B R L A
REAR CENTER
( SURROUND)
CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
A DVD
COMPONENT VIDEO AUDIO AUDIO DIGITAL
ZONE 2 OUT DIGITAL
VIDEO
B D–TV
/LD
C SAT
MONITOR OUT
FRONT IN
FRONT
OUT
REAR
( SURROUND)
SUB WOOFER SPLIT
MONO
REAR CTR
IN
OUT
REMOTE 1
IN
CTRL
OUT
+12V 10mA
MAX.
RS– 232C
REMOTE 2
CENTER IN
CENTER OUT
Y P B /C B P R /C R
R L
PREOUT/MAIN IN
CONTROL
MAIN IN
MAIN OUT
R L
VIDEO
DVD
PHONO GND
CD
S VIDEO L R R L
CABLE
SAT
IN
VCR 1
OUT
IN
VCR 2
OUT
IN
VCR 3
/DVR
OUT
VIDEO
6CH INPUT CENTER
SUB WOOFER
VCR 3 /DVR
1
MONITOR
OUT
2
D–TV /LD
L
SURROUND
MAIN
R
1
TUNER
CD–R
2
IN
( PLAY)
3
OUT
( REC)
4
MD/TAPE
IN
( PLAY)
3
OUT
( REC)
4
OPTICAL
IN
OPTICAL
OUT
COAXIAL
IN
w
D–TV
/LD
0
MD/
TAPE
6
SAT
q
DVD
9
CD–R
8
CD
7
CD–R
5
CABLE
4
DVD
3
CD
2
LD
LD
RF
( AC–3)
1
VOLTAGE SELECTOR
FRONT
REAR
REAR CENTER
CENTER
MAIN A OR B
A + B : 6 ΩMIN. /SPEAKER
: 4 ΩMIN. /SPEAKER
: 4 ΩMIN. /SPEAKER
: 4 ΩMIN. /SPEAKER
: 4 ΩMIN. /SPEAKER
: 8 ΩMIN. /SPEAKER
FRONT
REAR
REAR CENTER
CENTER
MAIN A OR B
A + B : 8 ΩMIN. /SPEAKER
: 8 ΩMIN. /SPEAKER
: 8 ΩMIN. /SPEAKER
: 8 ΩMIN. /SPEAKER
: 8 ΩMIN. /SPEAKER
: 16 ΩMIN. /SPEAKER
1 2 3
1 Composite VIDEO jack
Video signals input through the VIDEO jacks are the conventional
composite video signals.
2 S VIDEO jack
Video signals input through the S VIDEO jacks are separated into
luminance (Y) and color (C) video signals. The S-video signals
achieve high quality color reproduction. When you are using the S
VIDEO jacks, check the details in the owner’s manual that came
with the component being connected.
3 COMPONENT VIDEO jacks
Video signals input through the COMPONENT VIDEO jacks are
separated into luminance (Y) and color difference (P
B /C B , P R /C R )
video signals. The jacks are also separated into three for each signal.
The labels of the component video jacks may be different depend-
ing on the component (e.g. Y, C
B , C R / Y, P B , P R / Y, B-Y, R-Y/ etc.).
Component video signals provide the best quality in picture
reproduction. When you are using the COMPONENT VIDEO
jacks, check the details in the owner’s manual that came with the
component being connected.
Cautions
• Use a commercially available S-video cable when connecting to
the S VIDEO jacks, and commercially available video cables
when connecting to the COMPONENT VIDEO jacks.
• Each type of video jack works independently. Signals input
through the composite video, S-video, and component jacks are
output through the corresponding composite video, S-video, and
component jacks respectively.
• If your video monitor is connected only to the COMPONENT
VIDEO jacks of this unit, the OSD is not shown.
Note
• You can designate the input for the COMPONENT VIDEO A, B
and C jacks according to your component by using “8 I/O
ASSIGNMENT” on the SET MENU (see page 58 for details).