Yamaha GX707 - Manual (Page 26)

E
-16
CD player operation
Program play
You can program up to 20 tracks in any desired order.
1 When the CD player is being stopped, press PROG to prepare
for programming.
* “PROG” (9) and “P-01” (2) will light up on the display, and
all track numbers on the selected disc (7) will begin blinking.
2 If necessary, select the desired disc by pressing DISC SKIP .
* Just after you change the disc, the CD player reads the
contents of the newly selected disc for a few seconds. If you
go on to the next step during this internal operation, “WAIT”
(2) appears on the display and your operation is canceled.
3 Use the numeric buttons to select the desired track number.
* The selected track number (1) and the total play time of the
programmed tracks (2) will light up on the display, and it
will soon be replaced by the display of the next play order
(2). Programmed track numbers on the selected disc will stop
flashing and light up on the music calendar (7).
* Pressing TIME displays the total play time of the programmed
tracks (2) for about 1 second, and then it is replaced by the
display of the next play order (2).
4 Repeat steps 2 and 3 to program other tracks.
5
Press / to start the program play.
Notes
• If the total time of the programmed tracks becomes 100 minutes
or more, the first digit will not be displayed.
• The total time of the programmed tracks will not be displayed, if
track number 16 or higher is programmed.
• Skip ( / ) can be performed during play, but only within
the range of the programmed tracks.
• Search ( / ) can be performed during play to search all
tracks, including unprogrammed tracks.
To cancel a programmed sequence
Press while the CD player is being stopped.
To check (and correct) program data
1. Press PROG when the CD player is being stopped.
2. Every time is pressed, the track numbers and sequential
order of the programmed tracks can be checked one after
another. The display of the track number can be returned
(sequentially in reverse order) by pressing
.
3. If you want to correct the program data, press a numeric button
to select the track to replace the one displayed. The previously
programmed track will be cleared from the memory and the new
one will be programmed.
To complete the correction, press
PROG or / once again.
DISC 3 OPEN/ CLOSE DISC CHANGE DISC 2 DISC 1
PROGRAM B.BOOST MUSIC
ET/TUNING/BAND A/B/C/D/E
/
VOLUME
UP
DOWN
DOLBY NR
REC/
PAUSE
AUTO/
MANUAL
TIMER
MEMORY
TIME ADJ
RANDOM
HOUR
REPEAT TIME DISPLAY
MIN
DIGITAL AUDIO
HALL
ERSION
EDIT
PROG
S F REP
V A B OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TRACK
VCD PBC
TIMER
SLEEP
NOR TEST
PHANTOM
RANDOM TUNER
CD
MD
TAPE
M
HALL
MERSION
EDIT
PROG
S F REP
V A B OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TOTAL
TRACK
VCD PBC
TIMER
SLEEP
NOR TEST
PHANTOM
RANDOM TUNER
CD
MD
TAPE
TIME
TIME
Display information during programming
Play order Selected disc
Music calendar
Selected track number Total playing time
POWER
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
0
PRESET
TUNER +I0
PRESET
TIME
A
PROG
B
R.TIME
C
EDIT
D
DISC SKIP MODE
E
CD
/
5
3
2
5
, / (play/pause)
1,
PROG