Fein MultiMaster Marine - Manual (Page 12)

12 en
For your safety.
Read all safety warnings and all instruc-
tions. Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
for sanding small surfaces, corners and edges, for sawing
thin parts of steel sheet, wood and plastic, for scraping,
polishing, rasping, cutting and separating without water in
weather-protected environments, using the application
tools and accessories recommended by FEIN.
Special safety instructions.
Hold power tool by insulated gripping surfaces, when per-
forming an operation where the cutting accessory may con-
tact hidden wiring or its own cord. Cutting accessory
contacting a “live” wire will make exposed metal parts of
the power tool ‘“live” and shock the operator.
Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the work by
hand or against your body leaves it unstable and may lead
to loss of control.
Grasp the power tool in such a safe manner that your body
never comes into contact with the application tool, espe-
cially while working with application tools such as saw
blades or other blades pointed toward the grasping range.
Touching sharp tips or cutting edges can lead to injuries.
Wear personal protective equipment. Depending on the
application, use a face shield or safety goggles. Wear a
dust mask. Wear hearing protection. The eye protection
must be capable of protecting against flying particles gen-
erated by the various different operations. The dust mask
or respirator must be capable of filtering particles gener-
ated by your operation. Prolonged exposure to high
intensity noise may cause loss of hearing.
Wear protective gloves. Danger of injury due to sharp-
edged accessories.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection against
an electric shock will be ineffective. Adhesive labels are
recommended.
Clean the ventilation openings on the power tool at regular
intervals using non-metal tools. The blower of the motor
draws dust into the housing. An excessive accumulation
of metallic dust can cause an electrical hazard.
Before putting into operation, check the mains connection
and the mains plug for damage.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Character Unit of measure,
international Unit of measure, national Explanation
V V Rated voltage
P
1
W W Power input
P
2
W W Output
f Hz Hz Frequency
n
S
1/min 1/min Rated oscillation rate
L
wA
dB dB Sound power level
L
pA
dB dB Sound pressure level
L
pCpeak
dB dB Peak sound pressure level
K… Uncertainty
m/s
2
m/s
2
Vibration emission value (triax vector sum)
determined according to EN 60745
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
m, s, kg, A, mm, V, W,
Hz, N, °C, dB, min,
m/s
2
Basic and derived units of measure from the
international system of units SI.
WARNING
3 41 01 078 06 0.book Seite 12 Dienstag, 16. März 2010 7:39 07