Fein MultiMaster Marine - Manual (Page 13)

13 en
Handling hazardous dusts
For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to
one’s health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, and antifouling paints for vessels, can trig-
ger allergic reactions to the operator or bystanders and/
or lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of sanding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty
the dust collector/container in time, observe the material
manufacturer’s working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
At a glance.
The following numbering of the product fea-
tures refers to the illustrations at the beginning
of this Instruction Manual.
1 Quick-clamping lever
For clamping the tool.
2 Switch
For switching the power tool ON and OFF.
3 Thumbwheel for pre-selection of oscillating frequency
For pre-selection of oscillating frequency.
1=lowest oscillation rate.
6=highest oscillation rate.
4 Depth stop
For depth-of-cut adjustment .
5 Suction device
For dust-free operation, connect to a vacuum
cleaner .
6 Changing accessories, MultiMaster FMM250Q
Mount accessories with fastening element (6a).
7 Changing accessories, MultiMaster FMM250
Mount accessories with clamping screw (7b).
8 Tool holder
When mounting accessories, ensure positive lock-
ing.
9 Sanding sheet
Attach sanding sheet with Velcro backing.
10 Vibration-damping FEIN gel work gloves
Reduces the vibrational stress.
11 Standard accessories
Allen key (11c).
Operation of the power tool off power generators.
This machine is also intended to be powered by
a.c. generators with sufficient power output that
correspond with ISO 8528, design class G2. Com-
pliance with this Standard in particular is not given when
the so-called distortion factor exceeds 10%. When in
doubt, inform yourself about the generator in use.
Instructions for putting into operation.
Mounting the suction device (Figure 12).
➤ Mount the suction device step by step as shown
in the figures.
For connection with a FEIN Dustex or a vacuum cleaner,
various hose adapters are available as an accessory.
➤ To remove the suction device again, push the
clamp at the mark to the rear. (Figure 12-8)
Operating instructions.
Changing the tool.
Do not use accessories not specifically intended and recom-
mended for this power tool by FEIN. The use of non-original
FEIN accessories can lead to overheating of the power
tool and destroy it.
For adjustment of the most convenient working
position, the application tool can be mounted in
45° steps.
M ULTI M ASTER FMM250Q (F IGURE 6).
➤ Loosen the quick-clamping lever (1) and swivel
it to the stop.
➤ Pull out the fastening element (6a).
➤ Clean the tool holder (8), the application tool
and the fastening element (6a).
➤ Place the application tool exactly onto the star-
shaped tool holder (8). Pay attention that the appli-
cation tool has a flush fit.
➤ Insert the fastening element (6a) to the stop into
the tool holder.
➤ Swivel the quick-clamping lever (1) back until it
engages.
Protect your hand and fingers against bruising them
when locking the clamping lever. The clamping lever
snaps back vigorously by means of spring force.
M ULTI M ASTER FMM250 (Figure 7).
➤ Unscrew the clamping screw (7b).
➤ Clean the tool holder (8), the application tool
and the clamping screw (7b).
➤ Place the application tool exactly onto the star-
shaped tool holder (8). Pay attention that the appli-
cation tool has a flush fit.
➤ Tighten the clamping screw (7b) using the sup-
plied Allen key (11c).
Attaching/replacing the sanding sheet (Figure 9).
➤ Align the sanding sheet and press it onto the
sanding plate by hand.
➤ Firmly push the power tool via the sanding sheet
onto a flat surface and briefly switch the power
tool on. This provides for good adhesion of the
sanding sheet and prevents premature wear.
3 41 01 078 06 0.book Seite 13 Dienstag, 16. März 2010 7:39 07