Petzl ALVEO BEST - Manual (Page 2)

2 A20B_ALVEO_BEST_A205500C (270910)
75 mm 76 mm 77 mm 78 mm 80 mm
ALVEO BEST
DRAFT 1 - 28.10.10
Miniplan 1 verso
CAHIER
CAHIER
A205500C (270910)
miniplan 1 verso
Mounting the headlamp / Fixation de la lampe frontale
PIXA 1: E78AHB
PIXA 2: E78BHB
PIXA 3: E78CHB
3. Test / test Attaching hearing protection / Fixation des protections antibruit
Attaching
Clippage
Removing
Déclippage
Instructions for use / Mode d’emploi Accessories / Accessoires Spare parts / Pièces détachées
Replacement foam for ALVEO
Mousse de rechange pour ALVEO
A20210
Absorbent foam for ALVEO
Mousse absorbante pour ALVEO
A20200
Standard stickers for ALVEO
Autocollants standards pour ALVEO
A20100
Reflective stickers for ALVEO
Autocollants réfléchissants pour ALVEO
A20110
VIZIR face shield / Visière VIZIR
A15
1
(EN) ENGLISH
Helmet for work at height and
rescue
Field of application
This helmet is designed only for
work at height and rescue.
The ALVEO BEST helmet meets
the requirements of the EN 397
standard, except for the chin strap
and the internal vertical clearance
requirements. The chinstrap has a
strength of 50 daN (requirement
of the EN 12492 standard) to help
keep the helmet on the head in case
of a fall.
The ALVEO BEST meets optional
requirements of EN 397: Protection
against impacts down to -30 °C,
resistance to lateral deformation,
protection against accidental contact
with live conductors up to 440 V AC
and protection against molten metal
splash.
Do not use this helmet in activities
for which it is not designed.
Activities at height present a risk
of serious head injury. Wearing a
helmet can significantly reduce this
risk, but cannot entirely eliminate it.
In a major impact, the helmet
deforms to absorb the maximum
amount of energy possible,
sometimes to the point of destroying
the helmet.
WARNING
Activities involving the use of
this equipment are inherently
dangerous.
You are responsible for your own
actions and decisions.
Before using this product, you must:
- Read and understand all
instructions for use.
- Get specific training in its proper
use.
- Become acquainted with its
capabilities and limitations.
- Understand and accept the risks
involved.
Failure to heed any of these
warnings may result in severe
injury or death.
Responsibility
WARNING, specific training in the
activities defined in the field of
application is essential before use.
This product must only be used by
competent and responsible persons,
or those placed under the direct and
visual control of a competent and
responsible person.
Gaining an adequate apprenticeship
in appropriate techniques and
methods of protection is your own
responsibility.
You personally assume all risks and
responsibilities for all damage, injury
or death which may occur during
or following incorrect use of our
products in any manner whatsoever.
A205500C (270910)
2
If you are not able, or not
in a position to assume
this responsibility or to
take this risk, do not use
this equipment.
Nomenclature of parts
(1) Shell, (2) Headband,
(3) Headband adjustment wheels,
(4) Chin strap positioning buckles,
(5) Chin strap fastening and
adjustment buckle, (6) Side slots
for mounting hearing protection,
(7) Headlamp clips, (8) Front
headlamp mounting slot, (9) Face
shield mounting hole, (10) Internal
liner.
Principal materials: Acrylonitrile
Butadiene Styrene (ABS) shell,
polyester straps.
Inspection, points to
verify
Before each use, check the condition
of the shell and the headband
attachment system (verify there
are no cracks or deformation on
the outside or the inside...). Check
the condition of the webbing and
stitching. Verify that the headband
adjustment system and chinstrap
buckle are functioning properly.
WARNING, a major impact to the
helmet can significantly reduce its
protective properties without leaving
visible signs of damage. Retire your
helmet after a major impact.
Consult the details of the inspection
procedure to be carried out for each
item of PPE on the Web at www.
petzl.com/ppe
Contact PETZL if there is any doubt
about the condition of this product.
Instructions for use
1. Preparation
Use only the smooth areas for
stickers and other markings. PETZL
stickers are approved. For any other
stickers, verify their compatibility
with Acrylonitrile Butadiene Styrene.
Paint and stickers may contain
materials that, with time, can alter
the physical properties of the
helmet.
2. Adjustments
2a. Adjust the headband to
maximum size using the adjustment
wheels and place the helmet on
your head.
2b. Position the adjusters under
the ears. To adjust the chinstrap
backwards or forwards, slide the
webbing through the chinstrap
positioning buckles.
2c. Use the adjustment wheels to
increase or decrease the size of the
headband. You can adjust the height
of the headband on your forehead
(two adjustment holes for the
vertical position of the headband).
2d. Fasten the chinstrap using
the buckle. You must hear the
buckle “click” to ensure proper
fastening. Tighten the chinstrap to
fit comfortably. A correctly adjusted
chinstrap reduces the risk of the
helmet coming off accidentally.
You must pull on the chinstrap to
verify that the buckle is properly
fastened.
To open the buckle, press the button
on the chinstrap fastening buckle.
2e. Adjust the vertical position of
the headband adjustment system on
your nape by sliding it up or down
along the webbing.
ATTENTION, be sure there is no
slack in the webbing between the
headband adjustment system and
the shell of the helmet.
3. Test
Verify that the helmet is well seated
and centered on the head. A well-
adjusted helmet (minimal movement
front to back or side to side),
provides better protection.
+ 50°C / + 122°F
- 30°C / - 22°F
75 mm 76 mm 77 mm 78 mm 80 mm
ALVEO BEST
DRAFT 1 - 28.10.10
Miniplan 1 verso
CAHIER
CAHIER
A205500C (270910)
miniplan 1 verso
Mounting the headlamp / Fixation de la lampe frontale
PIXA 1: E78AHB
PIXA 2: E78BHB
PIXA 3: E78CHB
3. Test / test Attaching hearing protection / Fixation des protections antibruit
Attaching
Clippage
Removing
Déclippage
Instructions for use / Mode d’emploi Accessories / Accessoires Spare parts / Pièces détachées
Replacement foam for ALVEO
Mousse de rechange pour ALVEO
A20210
Absorbent foam for ALVEO
Mousse absorbante pour ALVEO
A20200
Standard stickers for ALVEO
Autocollants standards pour ALVEO
A20100
Reflective stickers for ALVEO
Autocollants réfléchissants pour ALVEO
A20110
VIZIR face shield / Visière VIZIR
A15
1
(EN) ENGLISH
Helmet for work at height and
rescue
Field of application
This helmet is designed only for
work at height and rescue.
The ALVEO BEST helmet meets
the requirements of the EN 397
standard, except for the chin strap
and the internal vertical clearance
requirements. The chinstrap has a
strength of 50 daN (requirement
of the EN 12492 standard) to help
keep the helmet on the head in case
of a fall.
The ALVEO BEST meets optional
requirements of EN 397: Protection
against impacts down to -30 °C,
resistance to lateral deformation,
protection against accidental contact
with live conductors up to 440 V AC
and protection against molten metal
splash.
Do not use this helmet in activities
for which it is not designed.
Activities at height present a risk
of serious head injury. Wearing a
helmet can significantly reduce this
risk, but cannot entirely eliminate it.
In a major impact, the helmet
deforms to absorb the maximum
amount of energy possible,
sometimes to the point of destroying
the helmet.
WARNING
Activities involving the use of
this equipment are inherently
dangerous.
You are responsible for your own
actions and decisions.
Before using this product, you must:
- Read and understand all
instructions for use.
- Get specific training in its proper
use.
- Become acquainted with its
capabilities and limitations.
- Understand and accept the risks
involved.
Failure to heed any of these
warnings may result in severe
injury or death.
Responsibility
WARNING, specific training in the
activities defined in the field of
application is essential before use.
This product must only be used by
competent and responsible persons,
or those placed under the direct and
visual control of a competent and
responsible person.
Gaining an adequate apprenticeship
in appropriate techniques and
methods of protection is your own
responsibility.
You personally assume all risks and
responsibilities for all damage, injury
or death which may occur during
or following incorrect use of our
products in any manner whatsoever.
A205500C (270910)
2
If you are not able, or not
in a position to assume
this responsibility or to
take this risk, do not use
this equipment.
Nomenclature of parts
(1) Shell, (2) Headband,
(3) Headband adjustment wheels,
(4) Chin strap positioning buckles,
(5) Chin strap fastening and
adjustment buckle, (6) Side slots
for mounting hearing protection,
(7) Headlamp clips, (8) Front
headlamp mounting slot, (9) Face
shield mounting hole, (10) Internal
liner.
Principal materials: Acrylonitrile
Butadiene Styrene (ABS) shell,
polyester straps.
Inspection, points to
verify
Before each use, check the condition
of the shell and the headband
attachment system (verify there
are no cracks or deformation on
the outside or the inside...). Check
the condition of the webbing and
stitching. Verify that the headband
adjustment system and chinstrap
buckle are functioning properly.
WARNING, a major impact to the
helmet can significantly reduce its
protective properties without leaving
visible signs of damage. Retire your
helmet after a major impact.
Consult the details of the inspection
procedure to be carried out for each
item of PPE on the Web at www.
petzl.com/ppe
Contact PETZL if there is any doubt
about the condition of this product.
Instructions for use
1. Preparation
Use only the smooth areas for
stickers and other markings. PETZL
stickers are approved. For any other
stickers, verify their compatibility
with Acrylonitrile Butadiene Styrene.
Paint and stickers may contain
materials that, with time, can alter
the physical properties of the
helmet.
2. Adjustments
2a. Adjust the headband to
maximum size using the adjustment
wheels and place the helmet on
your head.
2b. Position the adjusters under
the ears. To adjust the chinstrap
backwards or forwards, slide the
webbing through the chinstrap
positioning buckles.
2c. Use the adjustment wheels to
increase or decrease the size of the
headband. You can adjust the height
of the headband on your forehead
(two adjustment holes for the
vertical position of the headband).
2d. Fasten the chinstrap using
the buckle. You must hear the
buckle “click” to ensure proper
fastening. Tighten the chinstrap to
fit comfortably. A correctly adjusted
chinstrap reduces the risk of the
helmet coming off accidentally.
You must pull on the chinstrap to
verify that the buckle is properly
fastened.
To open the buckle, press the button
on the chinstrap fastening buckle.
2e. Adjust the vertical position of
the headband adjustment system on
your nape by sliding it up or down
along the webbing.
ATTENTION, be sure there is no
slack in the webbing between the
headband adjustment system and
the shell of the helmet.
3. Test
Verify that the helmet is well seated
and centered on the head. A well-
adjusted helmet (minimal movement
front to back or side to side),
provides better protection.
+ 50°C / + 122°F
- 30°C / - 22°F
75 mm 76 mm 77 mm 78 mm 80 mm
ALVEO BEST
DRAFT 1 - 28.10.10
Miniplan 1 verso
CAHIER
CAHIER
A205500C (270910)
miniplan 1 verso
Mounting the headlamp / Fixation de la lampe frontale
PIXA 1: E78AHB
PIXA 2: E78BHB
PIXA 3: E78CHB
3. Test / test Attaching hearing protection / Fixation des protections antibruit
Attaching
Clippage
Removing
Déclippage
Instructions for use / Mode d’emploi Accessories / Accessoires Spare parts / Pièces détachées
Replacement foam for ALVEO
Mousse de rechange pour ALVEO
A20210
Absorbent foam for ALVEO
Mousse absorbante pour ALVEO
A20200
Standard stickers for ALVEO
Autocollants standards pour ALVEO
A20100
Reflective stickers for ALVEO
Autocollants réfléchissants pour ALVEO
A20110
VIZIR face shield / Visière VIZIR
A15
1
(EN) ENGLISH
Helmet for work at height and
rescue
Field of application
This helmet is designed only for
work at height and rescue.
The ALVEO BEST helmet meets
the requirements of the EN 397
standard, except for the chin strap
and the internal vertical clearance
requirements. The chinstrap has a
strength of 50 daN (requirement
of the EN 12492 standard) to help
keep the helmet on the head in case
of a fall.
The ALVEO BEST meets optional
requirements of EN 397: Protection
against impacts down to -30 °C,
resistance to lateral deformation,
protection against accidental contact
with live conductors up to 440 V AC
and protection against molten metal
splash.
Do not use this helmet in activities
for which it is not designed.
Activities at height present a risk
of serious head injury. Wearing a
helmet can significantly reduce this
risk, but cannot entirely eliminate it.
In a major impact, the helmet
deforms to absorb the maximum
amount of energy possible,
sometimes to the point of destroying
the helmet.
WARNING
Activities involving the use of
this equipment are inherently
dangerous.
You are responsible for your own
actions and decisions.
Before using this product, you must:
- Read and understand all
instructions for use.
- Get specific training in its proper
use.
- Become acquainted with its
capabilities and limitations.
- Understand and accept the risks
involved.
Failure to heed any of these
warnings may result in severe
injury or death.
Responsibility
WARNING, specific training in the
activities defined in the field of
application is essential before use.
This product must only be used by
competent and responsible persons,
or those placed under the direct and
visual control of a competent and
responsible person.
Gaining an adequate apprenticeship
in appropriate techniques and
methods of protection is your own
responsibility.
You personally assume all risks and
responsibilities for all damage, injury
or death which may occur during
or following incorrect use of our
products in any manner whatsoever.
A205500C (270910)
2
If you are not able, or not
in a position to assume
this responsibility or to
take this risk, do not use
this equipment.
Nomenclature of parts
(1) Shell, (2) Headband,
(3) Headband adjustment wheels,
(4) Chin strap positioning buckles,
(5) Chin strap fastening and
adjustment buckle, (6) Side slots
for mounting hearing protection,
(7) Headlamp clips, (8) Front
headlamp mounting slot, (9) Face
shield mounting hole, (10) Internal
liner.
Principal materials: Acrylonitrile
Butadiene Styrene (ABS) shell,
polyester straps.
Inspection, points to
verify
Before each use, check the condition
of the shell and the headband
attachment system (verify there
are no cracks or deformation on
the outside or the inside...). Check
the condition of the webbing and
stitching. Verify that the headband
adjustment system and chinstrap
buckle are functioning properly.
WARNING, a major impact to the
helmet can significantly reduce its
protective properties without leaving
visible signs of damage. Retire your
helmet after a major impact.
Consult the details of the inspection
procedure to be carried out for each
item of PPE on the Web at www.
petzl.com/ppe
Contact PETZL if there is any doubt
about the condition of this product.
Instructions for use
1. Preparation
Use only the smooth areas for
stickers and other markings. PETZL
stickers are approved. For any other
stickers, verify their compatibility
with Acrylonitrile Butadiene Styrene.
Paint and stickers may contain
materials that, with time, can alter
the physical properties of the
helmet.
2. Adjustments
2a. Adjust the headband to
maximum size using the adjustment
wheels and place the helmet on
your head.
2b. Position the adjusters under
the ears. To adjust the chinstrap
backwards or forwards, slide the
webbing through the chinstrap
positioning buckles.
2c. Use the adjustment wheels to
increase or decrease the size of the
headband. You can adjust the height
of the headband on your forehead
(two adjustment holes for the
vertical position of the headband).
2d. Fasten the chinstrap using
the buckle. You must hear the
buckle “click” to ensure proper
fastening. Tighten the chinstrap to
fit comfortably. A correctly adjusted
chinstrap reduces the risk of the
helmet coming off accidentally.
You must pull on the chinstrap to
verify that the buckle is properly
fastened.
To open the buckle, press the button
on the chinstrap fastening buckle.
2e. Adjust the vertical position of
the headband adjustment system on
your nape by sliding it up or down
along the webbing.
ATTENTION, be sure there is no
slack in the webbing between the
headband adjustment system and
the shell of the helmet.
3. Test
Verify that the helmet is well seated
and centered on the head. A well-
adjusted helmet (minimal movement
front to back or side to side),
provides better protection.
+ 50°C / + 122°F
- 30°C / - 22°F