3 adjustment with the pc – VEGA VEGAFLEX 55P (Profibus PA) User Manual
Page 32
32
VEGAFLEX 55P (Profibus PA)
Setup
VEGA signal condit. instrument
Rx
VEGAMET 513, 514, 515, 602
50 … 100 Ohm
VEGAMET 614
no additional
VEGADIS 371
resistance
necessary
VEGAMET 601
200 … 250 Ohm
VEGASEL 643
150 … 200 Ohm
VEGAMET 513 S4, 514 S4
515 S4, VEGALOG EA card
100 … 150 Ohm
4.3 Adjustment with the PC
The adjustment with the PC and the adjust-
ment program VVO is not described in this
operating instructions manual, but in the
manual "VEGA Visual Operating (VVO)“.
Beside the adjustment of VEGAFLEX, you will
find in the manual VEGA Visual Operating
further information on the scope of the
adjustment options with the PC.
If you operate a sensor in conjunction with a
VEGA signal conditioning instrument, please
use an additional communication resistor acc.
to the following table:
Before you can set up the sensors with the
adjustment program VVO (VEGA Visual
Operating), they have to be integrated into
the Profibus system. First of all, address the
sensors and connect them to your PA seg-
ment. With the attached GSD file, you inte-
grate the sensors into your system.
To set up VEGA sensors with the adjustment
software VVO, the PC or the adjustment
station on which VVO is installed must be
equipped with a Profibus DP interface card
(e.g. from Softing). The PC or adjustment
station then communicates as Master-Class 2
participant on the DP bus with the VEGA
sensors on the PA bus segment.
Sensor
Sensor
Sensor
Sensor
VVO
Segment
coupler
Profibus PA
cable
Profibus DP-
interface card
(Messrs. Softing)
DP cable
To connect the PC to the DP bus, a standard
RS 485-DTE interface cable (Data Terminal
equipment) is required. With the cable, you
connect the DP interface card to the bus or
the segment coupler.
PC
PC
PC
PC
PC
BUS
BUS
BUS
BUS
BUS
Screen
1
1 Screen
– –
2
2 M24
RxD/TxD-P
RxD/TxD-P
RxD/TxD-P
RxD/TxD-P
RxD/TxD-P
3
3
3
3
3
3
3
3
3
3 RxD/TxD-P
RxD/TxD-P
RxD/TxD-P
RxD/TxD-P
RxD/TxD-P
(40)
– –
4
4 CNTR-P
GND
GND
GND
GND
GND
5
5
5
5
5
5
5
5
5
5 GND
GND
GND
GND
GND
(55)
– –
6
6 VP
– –
7
7 P24
RxD/TxD-N
RxD/TxD-N
RxD/TxD-N
RxD/TxD-N
RxD/TxD-N
8
8
8
8
8
8
8
8
8
8 RxD/TxD-N
RxD/TxD-N
RxD/TxD-N
RxD/TxD-N
RxD/TxD-N
(41)
– –
9
9 CNTR-P
Profibus-DP
DP bus (in brackets the
interface card
PIN number of the P+F
segment couplers)
After having connected the computer to the
Profibus DP cable, VVO can be started.