Rainbow Electronics MAX6964 - Manual (Page 4)

MAX6964
17-Output LED Driver/GPO
with Intensity Control
4 _______________________________________________________________________________________
PORT OUTPUT LOW VOLTAGE WITH 50mA
LOAD CURRENT vs. TEMPERATURE
PORT OUTPUT LOW VOLTAGE V
OL
(V)
0.1
0.2
0.3
0.4
0.5
0.6
0
MAX6964 toc04
TEMPERATURE (°C)
110 95 65 80 -10 5 20 35 50 -25 -40 125
V+ = 3.6V
V+ = 2.7V
V+ = 2V
PORT OUTPUT LOW VOLTAGE WITH 20mA
LOAD CURRENT vs. TEMPERATURE
MAX6964 toc05
TEMPERATURE (°C)
PORT OUTPUT LOW VOLTAGE V
OL
(V)
110 95 80 65 50 35 20 5 -10 -25
0.1
0.2
0.3
0.4
0.5
0.6
0
-40 125
ALL OUTPUTS LOADED
V+ = 3.6V V+ = 2.7V
V+ = 2V
PWM CLOCK FREQUENCY
vs. TEMPERATURE
MAX6964 toc06
TEMPERATURE (°C)
PWM CLOCK FREQUENCY (kHz)
110 95 80 65 50 35 20 5 -10 -25 -40 125
V+ = 3.6V
V+ = 2.7V V+ = 2V
0.925
0.950
0.975
1.000
1.025
1.050
0.900
NORMALIZED TO V+ = 3.3V, T A = 25°C
STANDBY CURRENT vs. TEMPERATURE
MAX6964 toc01
TEMPERATURE (°C)
STANDBY CURRENT (
µ
A)
110 95 65 80 -10 5 20 35 50 -25
1
2
3
4
5
6
7
8
9
10
0
-40 125
V+ = 3.6V
PWM ENABLED
V+ = 2.7V
PWM ENABLED
V+ = 2V
PWM DISABLED V+ = 2.7V
PWM DISABLED
V+ = 3.6V
PWM
DISABLED
V+ = 2V
PWM ENABLED
SUPPLY CURRENT vs. TEMPERATURE
(PWM DISABLED; f SCL = 400kHz)
MAX6964 toc02
TEMPERATURE (°C)
SUPPLY CURRENT (
µ
A)
110 95 65 80 -10 5 20 35 50 -25
10
20
30
40
50
60
70
0
-40 125
V+ = 3.6V
V+ = 2.7V
V+ = 2V
5
10
15
20
25
30
35
40
45
50
55
60
65
70
0
SUPPLY CURRENT vs. TEMPERATURE
(PWM ENABLED; f SCL = 400kHz)
MAX6964 toc03
TEMPERATURE (°C)
SUPPLY CURRENT (
µ
A)
110 95 65 80 -10 5 20 35 50 -25 -40 125
V+ = 3.6V
V+ = 2.7V
V+ = 2V
__________________________________________Typical Operating Characteristics
(T A = +25°C, unless otherwise noted.)
TIMING CHARACTERISTICS (continued)
(Typical Operating Circuit, V+ = 2V to 3.6V, T A = T MIN to T MAX , unless otherwise noted. Typical values are at V+ = 3.3V, T A = +25°C.)
(Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Capacitive Load for Each Bus Line C b (Note 3) 400 pF
RST Pulse Width t
W
1 ns
Output Data Valid t DV Figure 10 5 ns
Note 1: All parameters tested at T
A = +25°C. Specifications over temperature are guaranteed by design.
Note 2: A master device must provide a hold time of at least 300ns for the SDA signal (referred to V
IL of the SCL signal) to bridge
the undefined region of SCL’s falling edge.
Note 3: Guaranteed by design.
Note 4: C
b = total capacitance of one bus line in pF. t R and t F measured between 0.3 x V DD and 0.7 x V DD .
Note 5: I
SINK ≤ 6mA. C b = total capacitance of one bus line in pF. t R and t F measured between 0.3 x V DD and 0.7 x V DD .
Note 6: Input filters on the SDA and SCL inputs suppress noise spikes less than 50ns.