Asus T2-PH1 - Manual (Page 70)

4 - 1 2 4 - 1 2 4 - 1 2 4 - 1 2 4 - 1 2 C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack 1 before using Serial ATA hard disk drives.
• When using the connectors in S S S S S tandard IDE t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, connect the
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o l o r C o l o r C o l o r C o l o r C o l o r S e t t i n g S e t t i n g S e t t i n g S e t t i n g S e t t i n g U s e U s e U s e U s e U s e
S A T A 1 S A T A 1 S A T A 1 S A T A 1 S A T A 1 B l a c k B l a c k B l a c k B l a c k B l a c k M a s t e r M a s t e r M a s t e r M a s t e r M a s t e r B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k
S A T A 2 S A T A 2 S A T A 2 S A T A 2 S A T A 2 B l a c k B l a c k B l a c k B l a c k B l a c k S l a v e S l a v e S l a v e S l a v e S l a v e D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k
1 2 . 1 2 . 1 2 . 1 2 . 1 2 . S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] )
( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] ) ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] ) ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] ) ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
®
SATA connectors
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
On the motherboard, the Serial ATA connectors are only labeled as
“SATA.” Refer to the illustration below to identify the SATA1 and
SATA2 connectors.