ClimaCool UCR 30, 50 and 70 tons Manual - Manual (Page 13)

13
www.climacoolcorp.com
1 module 37 " 37 " 37 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
2 modules 71 5/8 " 71 5/8 " 71 5/8 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
3 modules 106 1/4 " 106 1/4 " 106 1/4 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
4 modules 140 7/8 " 140 7/8 " 140 7/8 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
5 modules 175 1/2 " 175 1/2 " 175 1/2 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
6 modules 210 1/8 " 210 1/8 " 210 1/8 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
7 modules 244 3/4 " 244 3/4 " 244 3/4 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
8 modules 279 3/8 " 279 3/8 " 279 3/8 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
9 modules 314 " 314 " 314 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
10 modules 348 5/8 " 348 5/8 " 348 5/8 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
11 modules 383 1/4 " 383 1/4 " 383 1/4 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
12 modules 417 7/8 " 417 7/8 " 417 7/8 " 55 1/2 " 55 1/2 " 55 1/2" " 65-1/8" " 65-1/8" " 65-1/8" "
Notes:
1. Modular chiller bank width dimensions above include

" between modules, plus 1
" for required end caps when piping for direct return (Refer to page 15 - Water Piping
Configuration- Figure 1) Example: 5 modules is 171 " width +2 " (end caps) + 4 x
" (clearance between header pipes) = 175
".
2. When piping 1 to 5 or more than 5 modules use reverse return (Refer to page 15 - Water Piping Configurations - Figure 2). Example: 7 modules 239 " + 2 " (end caps)
+ 6 x
" (clearance between header pipes) = 244 ".
Height (inches) Depth (inches)
UCR070 UCR050 UCR030 UCR070 UCR050
Model UCR
UCR030 UCR070 UCR050 UCR030
Width (inches)
Recommended Service Clearances and Bank Dimensions
Service Clearances
Bank Dimensions
Notes:
1. Allow 36” clearance for electrical panels and 30” clearance for rear access to modules.
2. Allow a minimum of 18” height clearance for service.
3. Local building or electrical codes may require additional clearance. Consult applicable codes.