Draw-Tite 75707 MAX-FRAME RECEIVER - Manual

Installation Instructions
GMC Sierra/Chevrolet Silverado 2500 & 3500 HD Pickups.
(All inc. Regular, Crew, Extended & Dually - 2 & 4WD Long & Short-bed)
GMC Denali HD Crew-Cab Pickup.
Part Numbers:
75707
87602
44653
75501
Vehicle
Frame
Bumper
75501
Hitch Shown In Proper Position
(Shown on short bed with bolt-on bracket)
Equipment Required:
Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating or
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distributing 12,000 (5448 Kg) 1200 (545 Kg)
Weight Carrying
Ball Mount
8000 (3632 Kg) 800 (363 Kg)
Wi i A L ti PU3
Bumper
Fascia
Spring shackle
Wrenches: 13mm, 21mm, 22mm, 3/4”, 7/8”
Drill Bits: None
Fastener Kit: 75707F
Wiring Access Location: PU3
Other items: Plastic cutting tool,
(short bed as needed. (heat shield)
Figure 1.
1
*4
*5
6
7
This side shows
short-bed
configuration
(2) Bolt-on brackets supplied. Use on
short-bed trucks only. Same bracket
j f h id
*3
*4
*8
2 1
1
5
4
*Universal bolt-on
bracket, use on
short-bed only.
Typical both sides
just rotate for other side.
Passenger’s side
Driver’s side
Frame
attachment
14mm
weldnuts
Qty. (4) Hex Bolt, M14 x 2.0 x 45mm CL10.9 Qty. (6) Hex Nut, 1/2”-13
Qty (4) Conical Toothed Washer 5/8” (black color)  Qty (2) Carriage Bolt 1/2”-13 x 2” Gr 5
This side shows
long-bed configuration,
do not use bolt-on
brackets.
1
2 6
5
1
2
1
2
2 1
9
See next page for detail on
short-bed trucks.
Bumper
attachment,
14mm weldnuts
9/16” Flat washer
1. Lower spare tire from underneath of truck for ease of installation. Also remove existing 14mm bolts from end of each truck frame rail.
Return bolts to vehicle owner. If truck has existing hitch remove bumper bolts also.
2. On short bed;trucks, remove rearmost 8mm bolt holding plastic heat shield to bottom of frame on passenger’s side. See picture 1. next page.
3. For short bed trucks, attach bolt-on brackets supplied with hitch to hitch brackets as shown above. Torque to specs below.
Qty. (4) Conical Toothed Washer, 5/8 (black color)  Qty. (2) Carriage Bolt, 1/2 -13 x 2 Gr.5
Qty. (4) Hex Bolt, 1/2”-13 x 1-1/2” Gr.5 (shortbed only) Qty. (2) Block,1-1/2” x 2” with square hole
Qty.(10) Conical Toothed Washer, 1/2” (gold color) Qty. (2) Block,1-1/2” x 2” with round hole (shortbed only)
2
3 7
6
4 8
4. For long-bed trucks, discard bolt-on brackets or give to vehicle owner explaining that they are not needed for 8’ bed applications.
5. Raise hitch into position locating slots in hitch over existing weldnuts in truck bumper and end of truck frame rails.
6. For short-bed trucks sandwich tab of plastic heat shield between hitch and frame underneath on passenger side of truck. In some cases it may
be necessary to trim plastic gusset on heat shield to allow shield to stay in place. See picture next page.
7. Install supplied 14mm bolts and conical toothed washers into existing weldnuts as shown above. On forward attachments install supplied
carriage bolts and blocks through access hole on inside or outside of frame and down through slots in bottom of truck frame and hitch.
8. Attach nuts to forward bolts both sides and torque nuts and metric bolts installed in previous step to specifications below.
9. Raise spare tire back into place. p p
Tighten 1/2”-13 Gr.5 bolts with torque wrench to 75 Lb.-Ft. (102 N*M) Tighten M14 x 2.0 CL10.9 bolts to 115 Lb.-Ft. (156 N*M).
z 2010 Cequent Performance Products Sheet 1 of 6 75707N 9-24-10 Rev. B
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Form: F205 Rev A 5-6-05