MAX PJR265(CE) - Manual (Page 9)

9
2. HAMMER SAFETY WARN-
INGS
1. BE SURE TO KEEP HANDS AWAY FROM
THE TRIGGER SWITCH AND DETACH
THE BATTERY PACK WHEN REPLACING
OR ADJUSTING THE BIT, WHEN AB-
NORMALITIES OCCUR, AND WHEN THE
EQUIPMENT IS NOT BEING USED
Leaving the Battery pack installed in these
situations may cause breakdowns or dam-
age.
2. HOLD TOOL BY INSULATED GRIPS
WHEN PERFORMING AN OPERATION,
BECAUSE THE TOOL'S BIT MAY CON-
TACT HIDDEN "LIVE" WIRE
Contacting with a "live" wire may make ex-
posed metal parts of the tool "electrified" and
shock the operator. Failure to do so may re-
sult in serious injury.
3. MAKE SURE THE BIT IS SECURED IN
PLACE BEFORE OPERATION
Failure to do so may result in serious injury.
4. DO NOT POINT THE TOOL AT ANYONE
Personal injury may result if the tool catches
an operator or anyone working near him.
While working with the tool, be extremely
careful not to bring hands, legs, and other
body parts near the bit of the tool.
5. NEVER MODIFY THE TOOL
Modifying the tool will impair performance
and operating safety. Any modification may
lead to serious injury and void the tool war-
ranty.
6. MAINTAIN THE TOOL IN GOOD OPER-
ATING CONDITION
(CHECK TIGHTNESS OF SCREWS BE-
FORE OPERATION)
To secure operating safety and ensure top
performance, keep the tool free of wear and
damage.
Under normal operation, the tool is de-
signed to produce vibration. Due to the vi-
bration, the screws can come loose, caus-
ing damage to the tool or serious injury.
Also keep the tool's hand grip dry and clean,
especially free of oil and grease.
7. LET THE TOOL WARM UP FOR SEV-
ERAL MINUTES BEFORE USE
In cold weather or when the tool has not
been used for a long period of time, the in-
ternal lubrication in the tool might not be in-
sufficient. In such cases, let the tool warm up
for several minutes by operating it with no
load. Lacking sufficient internal lubrication,
the tool might not operate at full perform-
ance.
8. MAKE SURE TO OPERATE THE TOOL ON
A FIRM FOOTING
Failure to do so may lead to serious injury.
9. MAKE SURE THERE IS NO ONE BELOW
WHEN USING THE TOOL IN HIGH LO-
CATIONS
Failure to do so may lead to serious injury of
the person below.
10. HOLD THE TOOL FIRMLY WITH BOTH
HANDS
Failure to do so may lead to serious injury.
11. KEEP HANDS AWAY FROM MOVING
PARTS
12. DO NOT LEAVE THE TOOL RUNNING
Operate the tool only when hand-held.
13. DO NOT TOUCH THE BIT OR PARTS
CLOSE TO THE BIT IMMEDIATELY AF-
TER OPERATION
These parts may be extremely hot. Touching
these parts may cause serious injury.
14. USE ONLY THE AUTHORIZED BATTERY
PACK
Use only MAX JPL925 battery pack. If the
tool is connected to a power supply other
than the authorized pack, such as a re-
chargeable battery, a dry cell, or a storage
battery for use in automobiles, the tool may
be damaged, break down, overheat, or even
catch on fire. Do not connect this tool to any
power supply except the MAX JPL925 bat-
tery pack.
15. TO ENSURE MAXIMUM PERFORMANCE,
FULLY CHARGE THE BATTERY BEFORE
USE
A new battery pack or one not used for ex-
tended periods may have self-discharged
and thus may need recharging to restore it to
a fully charged condition. Before operating
the tool, make sure to charge the Battery
pack with the designated MAX Battery
charger JC928.
PJR265_CE.book 9 ページ ２０１０年１０月１３日 水曜日 午後４時５１分