FEC DSP1500 (SAN3) User Manual
Enforce, Operation manual, Digital servo press
Advertising
Table of contents
Document Outline
- enForce Servo Press Manual
- Introduction
- Chapter 1: Outline
- Chapter 2: Specifications
- Chapter 3: System Description
- Chapter 4: System Setup & Wiring
- Design & build Guidelines
- SAN Unit Design & Mounting Dimensions
- Calculating Circuit Protection
- Input Power Supply Connection
- Motor Power-Resolver Connections
- Pre-Amplifier Connection
- External Control (I/O) Signal Connection
- I/O Recommended Connecting Circuit
- Input Signal Explanation
- Output Signal Explanation
- Syncronized Press Operation
- Operation Timing Chart
- SW1 - SAN Unit Number Setting
- External Monitor (MON) Signal Connection
- RS485 Interface Connection
- CN8 - Firmware Flash Connector
- Cable Connection Guidelines
- Tool Connections
- Brake Option
- Chapter 5: Power Up & Initial Chacks
- Chapter 6: System Operation
- DP*S - Display & Programming Unit
- DP2S & DP4S Serial Connection
- RS232C Output Format
- Function of Display & Operating Panel
- Run Status Mode Operating Instruction
- Run Status Mode Change
- Run Status Key Operation
- Real Time Display Mode
- Press Result Display Mode
- Parameter Display Mode
- Operating Condition Display
- Status Display
- Bypass Mode Operating Instruction
- Data Edit Mode
- Parameter Copying
- Data Number Conversion Table
- Organization of Parameters
- System Parameter Definitions
- Work Parameter Definitions
- Load Control (Method 0)
- Distance Control (Method 1)
- Specified Point Load Judgment (Method 2 - Type 1)
- Load Rise Detection (Method 2 - Type 2)
- Time Controlled Press (Method 3)
- Load Drop Detection (Method 4)
- Specified Range Peak Load Judgment (Method 5)
- Load Drop Detection - Point Stop (Method 6)
- Distance Control with Load Limit (Method 7)
- Operation Steps
- Operation Finish Modes
- Data Numbers 10, 11 & 12
- Data Numbers 13 & 14
- Data Number 15, 23 & 16
- Data number 17, 18 & 24
- Data Number 20, 21, 22, 30~33, 40, 50, 41 & 42
- Data Number 51~54, 60 & 61
- Data Number 62, 63 & 64
- Step Press & Return Operations
- External LVDT Sensor
- Chapter 7: Maintenance & Inspection
- Chapter 8: Troubleshooting
- Abnormal Display
- [A1_*] - Load Cell Abnormals
- [A2_*] - Offset Load Abnormals
- [A3_*] - Preamplifier Errors
- [A4_*] - System Memory Errors
- [A5_*] - Servo Amplifier Response Errors
- [A6_*] - Servo Type Errors
- [A7_*] - Internal Errors
- [A8_*] - Servo Amplifier Errors
- [A9_*] - Parameter Errors
- Questions & Answers
- Appendix A: Reference Drawings
- Power Wiring Reference
- PLC I/O Wiring Reference - Allen Bradley (SLC)
- PLC I/O Wiring Reference - Omron (CS1)
- PLC I/O Wiring Reference - Mitsubishi (A1S)
- PLC I/O Wiring Reference - GE 90-30 Series
- PLC I/O Wiring Reference - Modicon (984)
- SAN3 Unit Connection Reference
- System Transformers
- Motor-Resolver Homerun Cable (SAN3-24S, 40S)
- Motor-Resolver Homerun Cable (SAN3-120S with RM4 Motor))
- Motor-Resolver Homerun Cable (SAN3-120S with RM5 Motor)
- Resolver Homerun Cable (SAN3-120S with RM5 Motor
- Load Cell (Pre-Amplifier) Homerun Cable (SAN3-24S, 40S, 120S)
- Motor-Resolver Extension Cable (SAN3-24S, 40S, 120S with RM4 Motor, also as Resolver Extension for SAN3-120S with RM5 Motor)
- Motor Extension Cable (SAN3-120S with RM5 Motor)
- Load Cell (Pre-Amplifier) Extension Cable (SAN3-24S, 40S, 120S)
- SAN3-24S/40S Power Cable
- SAN3-120S Power Cable
- I/O Connection Cable
- I/O Proximity Switch Breakout Adapter
- Proximity Switch Homerun Cable
- Proximity Switch Tool / Extension Cable
- Brake Unit Homerun Cable
- Brake Unit Extension Cable
- External Brake Unit Cable
- RS-485 Jumper Cable
- RS-485 to RS-232 PC Converter Cable