Heat Storm HS-1000-W - Manual (Page 4)

The heater keeps blowing air when the leaf
symbol is not red or green
The heater does not blow warm air
“E1” is displayed on the control panel
“E2” is displayed on the control panel
“EE” is displayed on the control panel
“EH” is displayed on the control panel
The heater is functioning as it should. This is the cool down phase. The heater will run for
several minutes to cool down the internal components. This increases the lifespan of the
infrared elements.
A -Check if the air inlet is blocked or the air filter is dirty and needs to be cleaned.
B -The ambient temperature is higher than the thermostat setting.
C - Disconnect the unit from the wall outlet for 2 hours. After 2 hours plug the unit back into
wall outlet. If the problem persists call customers service.
One quartz infrared tube may be malfunctioning.
It has been detected that more than one tube is malfunctioning. Disconnect the heater from
the wall outlet and call customer service.
The temperature sensor needs to be reset. Turn the heater off for at least 30 minutes.
The heater is too warm. It is possible the filter is obstructed or that the fan is not functioning.
Turn the heater to the off position. If the fan is running, let the heater cool down. Once the fan quits running
unplug the heater and call customer service.
operatinG instructions cont.
THERMOSTAT CALIBRATION
Thermostat readings can vary based on the environment. If desired, the thermostat on the heater can be manually calibrated to
match central HVAC system.
NOTE: Thermostat calibration can only be performed using the Control Panel on the heater and is not available using the remote control.
NOTE: Typically Heat Storm Infrared Heater thermostats are more accurate than home central thermostats. Changing your Heat Storm
Infrared Heater to match your central system may reduce its efficiency.
To adjust the thermostat:
Press the Up & Down Arrow at the same time and then also press the on/off button and hold all three buttons down for
5 seconds to begin calibration.
Use the up and/or down buttons to adjust the thermostat.
After 5 seconds without control input the heater will exit thermostat calibration.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. This Class B digital
apparatus complies with Canadian ICES-003.
WASHABLE LIFETIME FILTER SYSTEM
Heat Storm
™ Infrared Heaters come equipped with a washable lifetime filter which is easy to clean. (The manufacturer recommends
the filter to be cleaned regularly as needed.) To do this, follow these steps:
Press both tabs to remove the filter cover and remove the filter, noting which side of the filter receives air flow into the heater.
Run warm tap water over the filter, the opposite direction of air flow, until water runs clear. The filter might excrete some filtered
residue, so be cautious not to drip on any stainable surfaces such as carpeting. You can also soak the filter in water mixed with a
small amount of mild dish soap (remember to rinse well with clean water after soaking filter).
Shake the filter over a sink until excess water is removed and allow it to drip dry completely before reinstalling.
DO NOT force or attempt to speed the filter drying process by using any alternative methods.
ENSURE that the filter is completely dry before inserting back into the air inlet and replacing covers.
Reinstall the filter and replace cover.
WARNING
ANY REQUIRED SERVICE OTHER THAN FILTER MAINTENANCE SHOULD ONLY BE PERFORMED BY AN AUTHORIZED
SERVICE REPRESENTATIVE
REPLACING THE REMOTE CONTROL BATTERY
When the remote control stops operating or its range seems reduced, it is time to replace the battery with a new one.
The battery compartment is located on the back end of the remote.
Press and slide the battery door open and remove the old battery.
Insert 2pcs AAA batteries, checking that the + and - sides of the battery match inside the battery compartment.
Replace the battery compartment door.
NOTE: Do not mix old and new batteries. Do not mix alkaline, standard (carbonzinc), or rechargeable (nicad, nimh, etc) batteries.
DISPOSAL OF USED BATTERIES
Battery may contain hazardous substances which could endanger the environment and human health.
This symbol marked on the battery and/ or packaging indicates that used battery shall not be treated as municipal waste.
Batteries should be disposed of at an appropriate collection point for recycling.
By ensuring the used batteries are disposed of correctly, you will help prevent potential negative consequences for the
environment and human health. The recycling of materials will help to conserve natural resources. For more information about
collection and recycling of used batteries, please contact your local municipality or your waste disposal service.
trouBle sHootinG GuiDe