TREND NBOX(B)TMNE, G, H - Manual (Page 14)

14 NBOX(B)TMNE, G, H Trend Modem Node Controller Installation Instructions TG200729 Issue 2, 07/01/2009
NBOX(B)TMNE, G, H Installation Instructions
1.4 Installation - Configuration
(continued)
Close MBOX
if fitted in ENCLS/MBOX/IQ22x
30
b a
2 Limitations of Use
2.1 TMNH INTEGRAL MODEM (MT5600SMI-92)
2.1.1 Approvals
The CE and UL Approvals are defined in the Specification (Environmental) section of the TMNE, G, H data sheet (TA200734).
2.1.2 General
Host Equipment: The TMNH consists of the TMN host with the attached modem daughter board.The TMN host fully complies with the requirements
necessary for the EC24 modem regulatory requirements if it is operated within the specification defined in the TMNE, G, H data sheet (TA200734).
The modem is supplied to be used solely within the TMNH.
Safety: The modem comprises two sections of circuitry, namely a telecommunications interface and a host interface, which are separated by a safety
barrier that meets the reinforced level of isolation at 250Vrms. The modem cannot be used in host equipment that use or generate voltages in excess
of 250 Vrms.
The telecommunications interface is approved to be connected to telecommunication network voltage circuits which may carry dangerous voltages.
The telephone cord must remain disconnected from the telecommunications systems until the MT5600SMI-92 modem has been installed within a host
which provides the necessary protection for the operator. If it is subsequently desired to open the host equipment for any reason, the telephone cord
must be disconnected prior to effecting access to any internal parts which may carry telecommunication network voltages.
The integrity of the telephone line cord, connected to the modem, should not be compromised by wear or proximity to hazardous voltages, as defined
by EN60950.
The modem RJ11 PSTN network connector port type is TNV-3.
The local environment within the host must not be subject to conductive pollution or to dry non-conductive pollution which could become conductive
due to condensation.
Power is supplied to the modem through the host interface connector.
Network: External control software for this unit must comply with the following requirements. No other modes of operation should be used on the
PSTN and the use of such modes invalidates the approval.
1.
It must not allow the “S” register values to be set outside the following ranges: S6 (delay for blind dialling): 4 only, ie default value.
2. When dialling out, the number of “,” pauses inserted between digits in a dialled number must not exceed 5.
The modem is suitable for connection to PSTN direct exchange lines and/or to an approved private branch exchange. It may be connected to any
PSTN direct exchange line except as an extension to a pay-phone, or shared service.
The modem has a REN (ringer equivalence number) of 0.1B. The REN is a customer guide indicating the maximum number of items of apparatus
that should be connected simultaneously to the line. The total REN value must not exceed the maximum REN value of 4.
2.1.3 Country Specific Information
USA
FCC Part 15 Regulation
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference that may cause undesired operation.
WARNING – Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
47 CFR Part 68 Telecom
1. This equipment complies with Part 68 of the 47 CFR rules and the requirements adopted by the ACTA. Located on this equipment is a label
that contains, among other information, the registration number and ringer equivalence number (REN) for this equipment or a product identifier in
the format:
The registration number is AU7/USA-46014-MD-E
The REN is 0.1B
REN: For Canada the sum of the RENs of all the devices must not exceed five”.
The jack plug used to connect the TMNH to the premises wiring and telephone network is RJ11, which complies with the applicable 47 CFR part
68 rules and requirement adopted by the ACTA
Canada
Regulatory Requirements for Canada
The following requirements are established under section 69.3 of the Telecommunications Act for purposes of section 5 of the
Telecommunications Apparatus Regulations.
The equipment bears the following identifying marks, which are permanently affixed to the equipment:
(a) The registration number — Specifications of this mark are given in the document: IC: 125 1142A
(b) The model identification number under which the product was registered: MT5600SMI