TREND NBOX(B)TMNE, G, H - Manual (Page 15)

NBOX(B)TMNE, G, H Trend Modem Node Controller Installation Instructions TG200729 Issue 2, 07/01/2009 15
Installation Instructions NBOX(B)TMNE, G, H
2 Limitations of Use
(continued)
“This product meets the applicable Industry Canada technical specifications”
The REN is 0.1B
REN: For Canada the sum of the RENs of all the devices must not exceed five”.
I ndustry Canada
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Reglement Canadien sur le matériel brouilleur.
New Zealand
New Zealand Telecom Warning Notice
1. The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum
conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different
make or model, nor does it imply that any product is compatible with all of Telecom’s network services. This equipment is not capable under all
operating conditions of correct operating conditions of correct operation at the higher speed which it is designated. 33.6 kbps and 56 kbps
connections
are likely to be restricted to lower bit rates when connected to some PSTN implementations. Telecom will accept no responsibility should
difficulties arise in such circumstances.
2. Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair.
3. This modem shall not be used in any manner which could constitute a nuisance to other Telecom customers.
4. This device is equipped with pulse dialing, while the Telecom standard is DTMF tone dialing. There is no guarantee that Telecom lines will
always continue to support pulse dialing. Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give
rise to ‘bell tinkle’ or noise and may also cause a false answer condition. Should such problems occur, the user should NOT contact the
Telecom Faults Service. The preferred method of dialing is to use DTMF tones, as this is faster than pulse (decadic) dialing and is readily
available on almost all New Zealand telephone exchanges.
7. Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the host associated with this device. The
associated equipment shall be set to operate within the following limits for compliance with Telecom’s Specifications:
For repeat calls to the same number: There shall be no more than 10 call attempts to the same number within any 30 minute period for any
single manual call initiation, and the equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and
the beginning of the next attempt.
For automatic calls to different numbers:
The equipment shall be set to ensure that automatic calls to different numbers are spaced such that there is no less than 5 seconds between
the end of one call attempt and the beginning of another.
8. For correct operation, total of the REN’s of all devices connected to a single line at any time should not exceed 5.
South Africa
This modem must be used in conjunction with an approved surge protection device.
International use
The modem is approved in the UK, USA,- Australia, Austria, Belgium, Canada, China, Cyprus, Denmark, Eire, Finland, France, Germany, Greece,
Holland, Hong Kong, Hungary, India, Italy, Japan, Luxembourg, New Zealand, Norway, Poland, Portugal, Russia, Singapore, Spain, Sweden,
Switzerland, and many other countries. Check with Technical support for other countries.
If a country is not supported, the TMNE may be used with an external modem which is approved in that country.
International Modem Restrictions
Some dialing and answering defaults and restrictions may vary for international modems. Changing settings may cause a modem to become
non-compliant with national telecom requirements in specific countries. Also note that some software packages may have features or lack
restrictions that may cause the modem to become non-compliant.
EMC, Safety, and R&TTE Directive Compliance
The CE mark is affixed to this product to confirm compliance with the following European Community Directives: Council Directive 89/336/EEC
of 3 May 1989 on the approximation of the laws of Member States relating to electromagnetic compatibility; and Council Directive 73/23/EEC of
19 February 1973 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage
limits; and Council Directive 1999/5/EC of 9 March on radio equipment and telecommunications terminal equipment and the mutual recognition
of their conformity.
2.2 TMNG Integral GSM Modem (/EUR: MTSMC-G-F1, /USA: MTSMC-G-F2)
2.2.1 Safety Standards
THIS GSM MODEM COMPLIES WITH ALL APPLICABLE RF SAFETY STANDARDS.
This GSM modem meets the standards and recommendations for the protection of public exposure to RF electromagnetic energy established
by governmental bodies and other qualified organizations, such as the following :
Directives of the European Community,
Directorate General V in Matters of Radio Frequency Electromagnetic Energy
2.2.2 RF Exposures (/USA: MTSMC-F-F2)
Pursuant to 47 CFR § 24.52 of the FCC Rules and Regulations, personal communications services (PCS) equipment is subject to the radio
frequency radiation exposure requirements specified in § 1.1307(b), § 2.1091 and § 2.1093 as appropriate.
The TMNG/USA Modem is a GSM (PCS 1900) terminal which operates in the US licensed PCS frequency spectrum. The device transmits over
the 1850-1910 MHz band and receives over the 1930- 1990 MHz Band. Mult-Tech Systems, Inc. certifies that it has determined that the Modem
complies with the RF hazard requirements applicable to broadband PCS equipment operating under the authority of 47 CFR Part 24, Subpart E
of the FCC Rules and Regulations. This determination is dependent upon installation, operation and use of the equipment in accordance with all
instructions provided.
The modem is designed for and intended to be used in fixed and mobile applications. “Fixed” means that the device is physically secured at
one location and is not able to be easily moved to another location. “Mobile” means that the device is designed to be used in other than fixed
locations and generally in such a way that a separation distance of at least 20 cm is normally maintained between the transmitter’s antenna and
the body of the user or nearby persons. The Modem is not designed for or intended to be used in portable applications (within 20 cm of the
body of the user) and such uses are strictly prohibited.
To ensure that the unit complies with current FCC regulations limiting both maximum RF output power and human exposure to radio frequency
radiation, a separation distance of at least 20 cm must be maintained between the unit’s antenna and the body of the user and any nearby
persons at all times and in all applications and uses. Additionally, in mobile applications, maximum antenna gain must not exceed 3 dBi (to
comply with Section 24.232(b) and is limited to 7 dBi for fixed applications. Finally, the tune-up procedure for the O9EM2113 ensures that the
maximum RF output power of the device does not exceed 30.0 dBm within the variations that can be expected due to quantity production and
testing on a statistical basis.
2.2.3 GSM compliance (/EUR: MTSMC-G-F1)
The SocketModem is in compliance with reference regulations: EN301 511 V7.0.1
2.2.4 CE Label (/EUR: MTSMC-G-F1)
The Wireless SocketModem is CE compliant, which implies that the modem is in conformity with the European Community directives and it bears the
CE label.