Tyrex TY5100 - Manual (Page 13)

13
T r o u b l e s h o o t i n g

I d e n t i f i c a c i ó n d e F a l l a s

D é p a n n a g e
Problem or Symptom
Tool will not start or runs slowly.
Tool will not drive screw into desired substrate.
Tool does not fully drive fastener.
Tool does not advance fastener.
Screws fall out of collation during drive.
Bit will not install.
Bit slips off screw or screw is driven at an angle.
Fastener Jams
Slide Mechanism “sticks” or returns slowly.
Tool Overheats
Pushing force becomes excessive
Bit falls out.
Bit does not release.
Feed mechanism “locks up”.
Probable Cause
Trigger switch is defective.
Broken motor lead.
No electrical power.
Damaged cord.
Bit is worn.
Power capabilities of the tool have been exceeded.
Depth of drive not set properly.
Bit is worn or clogged.
Excessive spring debris.
Tool is in reverse.
Screw length is improperly set.
Return spring is weak.
Defective collation material.
Worn sprocket.
Screw riding high in collation.
Collation excessively hot.
Nose Piece loose.
Bit guide has worn.
Bit not properly inserted into drive shaft.
Not a TyRex bit.
Tool is slid forward during drive.
Tool is misaligned.
Bit guide has worn.
Screw length improperly set.
“Nosepiece” screw is loose.
Bit guide has worn.
Screw not seated properly in collation material.
Bit severely worn.
“Nosepiece” damaged or bent.
Debris build-up in mechanism.
Bent Nosepiece.
Weak return spring.
Tough drive application requires too much torque.
Clogged vents.
Slide body has worn.
Improper installation.
Worn drive shaft assembly.
Clutch faces not aligned.
Mechanism jammed.
Latch lever bound up.
Latch spring broken.
Corrective Action
Replace trigger switch.
Replace wiring harness.
Check power source. (fuse)
Replace cord.
Replace bit.
Refer to operators manual for appropriate applications.
Adjust depth of drive for deeper penetration.
Replace or clean bit.
Replace or clean spring.
Check for forward operation.
Refer to operators manual to adjust screw length.
Replace return spring.
Return to authorized TyRex service representative.
Replace slide body assembly.
Correct by hand or replace strip.
Keep strips in shade or cool location.
Hold tool firmly while driving.
Replace slide body assembly.
Drop bit straight into opening. Rotate. Push hard.
Return to authorized TyRex service repesentative.
Replace bit.
Try another strip of fasteners.
Replace slide body assembly.
Refer to manual for adjustment of screw length.
Tighten screw.
Replace slide body assembly.
Try another strip of fasteners.
Replace bit.
Replace “Nosepiece”.
Clean mechanism.
Replace Nosepiece.
Replace return spring.
Allow tool to cool and discontinue use in this application.
Be sure vents are open and free of debris.
Replace slide body. Return to TyRex for service.
Consult manual for proper installation technique.
Replace drive shaft assembly.
Pulse motor while using release button.
Rap bit sharply on workpiece (wood).
Lube (2 drops light oil) latch lever.
Replace latch spring.
TECHNICAL SPECIFICATIONS
�oltage 120v
Current 4.3 amps
Frequency 60Hz
RPM 5000
Weight 4.8 lbs.
Height 8”
Length 15
3/4 ”
Width 3”
Fastener
50 screws
Capacity (one strip)
Fastener 1-2”
Range #6-#8
thd.
TY5100 TyRex offers a full line of
screws and accessories for
your TyRex tools, including:
 Bits
 Case
 Allen Wrenches
 Safety Glasses
For more information or a
complete illustrated catalogue
of TyRex accessories, ask your
representative for #MK336.
ACCESORIES