Yokogawa AXFA14G/C - Manual (Page 42)

IM 01E20F02-01E 7-2
7. DEVICE INFORMATION
Table 7.3 Contents of DEVICE_STATUS_3 (Index 1047)
T0703.EPS
0 0x00000001 30:Sig Overflow Input signal error
1 0x00000002 31:Empty Pipe Flowtube is not filled with fluid
2 0x00000004
3 0x00000008 33:Adhesion Alm Electrode adhesion alarm
4 0x00000010
5 0x00000020
6 0x00000040
7 0x00000080
8 0x00000100
9 0x00000200
10 0x00000400
11 0x00000800
12 0x00001000
13 0x00002000
14 0x00004000
15 0x00008000
16 0x00010000 110:AI Lo Lo Alm AI process alarm
17 0x00020000 111:AI Hi Hi Alm AI process alarm
18 0x00040000 112:PID Lo Lo Alm PID process alarm
19 0x00080000 113:PID Hi Hi Alm PID process alarm
20 0x00100000
21 0x00200000
22 0x00400000
23 0x00800000
24 0x01000000
25 0x02000000
26 0x04000000
27 0x08000000
28 0x10000000
29 0x20000000
30 0x40000000
31 0x80000000
bit Hex Indicator description
Table 7.4 Contents of DEVICE_STATUS_4 (Index 1048)
T0704.EPS
0 0x00000001 40:RS O/S Mode RS. MODE_BLK.Target is O/S mode
1 0x00000002 41:TB O/S Mode TB. MODE_BLK.Target is O/S mode
2 0x00000004 42:AI FB O/S Mode AI. MODE_BLK.Target is O/S mode
3 0x00000008 43:IT1 FB O/S Mode IT1. MODE_BLK.Target is O/S mode
4 0x00000010 44:IT2 FB O/S Mode IT2. MODE_BLK.Target is O/S mode
5 0x00000020 45:DI1 FB O/S Mode DI1. MODE_BLK.Target is O/S mode
6 0x00000040 46:DI2 FB O/S Mode DI2. MODE_BLK.Target is O/S mode
7 0x00000080 47:AR FB O/S Mode AR. MODE_BLK.Target is O/S mode
8 0x00000100 48:PID FB O/S Mode PID. MODE_BLK.Target is O/S mode
9 0x00000200
10 0x00000400
11 0x00000800
12 0x00001000
13 0x00002000
14 0x00004000
15 0x00008000
16 0x00010000
17 0x00020000
18 0x00040000
19 0x00080000
20 0x00100000
21 0x00200000
22 0x00400000
23 0x00800000
24 0x01000000
25 0x02000000
26 0x04000000
27 0x08000000
28 0x10000000
29 0x20000000
30 0x40000000
31 0x80000000
bit Hex Indicator description
Table 7.5 Contents of DEVICE_STATUS_5 (Index 1049)
T0705.EPS
0 0x00000001 50:Span > 10m/s Span flow velocity setting is 11 m/s or more
1 0x00000002 51:Span < 0.1m/s Span flow velocity setting is 0.05 m/s or less
2 0x00000004
3 0x00000008 57:Dens Set Err Mass units have been selected for Base Flow Unit but
density is set to zero.
4 0x00000010 71:Meas Mod Set Measure Mode is set to Enhanced DF without selecting
an optional code HF1 or HF2.
5 0x00000020 72:Size Set Err A value of 3000.1 mm or more is set for Nominal Size.
6 0x00000040 73:Adh Set Err The condition in Adhesion detection level,
Level:1 Ͻ Level:2 Ͻ Level:3 Ͻ Level:4 is not satisfied.
7 0x00000080
8 0x00000100
9 0x00000200
10 0x00000400
11 0x00000800
12 0x00001000
13 0x00002000
14 0x00004000
15 0x00008000
16 0x00010000 120:IT1 Clock Per Err IT1 CLOCK_PER set value is smaller than excecution period
17 0x00020000 121:IT2 Clock Per Err IT2 CLOCK_PER set value is smaller than excecution period
18 0x00040000 122:AR Range Set Err RANGE_HI ϾRANGE_LO is not satisfied
19 0x00080000
20 0x00100000
21 0x00200000
22 0x00400000
23 0x00800000
24 0x01000000
25 0x02000000
26 0x04000000
27 0x08000000
28 0x10000000
29 0x20000000
30 0x40000000
31 0x80000000
bit Hex Indicator description
Table 7.6 Contents of DEVICE_STATUS_6 (Index 1050)
T0706.EPS
0 0x00000001 80:Adhesion Wng Slight adhesion to electrodes.
1 0x00000002
2 0x00000004 82:Auto Zero Wng Results of automatic zero adjustment are
higher than the rated value.
3 0x00000008
4 0x00000010 85:Flow Vel Over PRIMARY_VALUE exceeds 108% of Span
5 0x00000020
6 0x00000040
7 0x00000080
8 0x00000100
9 0x00000200
10 0x00000400
11 0x00000800
12 0x00001000
13 0x00002000
14 0x00004000
15 0x00008000
16 0x00010000
17 0x00020000
18 0x00040000
19 0x00080000
20 0x00100000
21 0x00200000
22 0x00400000
23 0x00800000
24 0x01000000
25 0x02000000
26 0x04000000
27 0x08000000
28 0x10000000
29 0x20000000
30 0x40000000
31 0x80000000
bit Hex Indicator description