Document Outline

• Software License Agreement
• Contents
• Chapter 1 Before Using the Software
  • 1.1 Functional Overview of MXLOGGER
    • Functional Overview
    • Logger
    • Viewer
    • Calibrator
  • 1.2 MXLOGGER Operation Guide
    • Flow of Operations during Installation
    • Overview of Operations
  • 1.3 PC System Requirements
  • 1.4 Setting Up MXLOGGER
    • Setup Procedure
    • Installation Result
  • 1.5 Starting and Exiting Software Programs
• Chapter 2 Logger
  • 2.1 Searching MX100 Data Acquisition Units and Configuring the Network
    • Searching for MX100s
    • Setting Up the Network
  • 2.2 Configuring the System
    • Selecting the MX100s That Are to Monitor the Data
    • Retrieving/Setting Module Configuration Information
    • Assigning Input Modules to Measurement Groups
    • Configuring a System Using MX100s That Are Not Connected
    • Setting the A/D Integration Time
    • Setting the Temperature Unit for TC and RTD
    • MX100 Response Check
    • CF Card Information
    • Setting the Write Mode of the CF Card
  • 2.3 Setting the Data Acquisition Conditions
    • Data Acquisition Conditions
    • Automatic Start Function
    • Setting the Measurement Channels and Computation Channels to Be Recorded
  • 2.4 Setting the Measurement Conditions (Measurement Channel Settings)
    • Setting the Input Mode
    • Setting the Measuring Range
    • Setting the Span
    • Setting the Scale (Only When Scaling)
    • Setting the Reference Channel for Difference Input (Valid Only When Measuring the Difference with Respect to the Measured Value of the Reference Channel)
    • Setting the Remote RJC Reference Channel (Valid Only When the Input Mode Is Set to RRJC (TC))
    • Setting the Unit, Tag Number, and Tag Comment
    • Setting the Time Constant of the First-Order Lag Filter (Valid Only When the Input Mode Is Set to Something Other than DI)
    • Setting the Burnout (Valid Only When the Input Mode Is Set to TC)
    • Setting the RJC (When the Input Mode Is Set to TC)
    • Setting the Initial Balancing for Strain Input Channels (Only When the Input Mode Is Set to STR)
    • Importing Tag Numbers and Tag Comments
    • When Setting the Measurement Conditions for Each Channel Individually
  • 2.5 Setting Computations (Setting the Computation Channels)
    • Setting the Expression
    • Setting the Span
    • Setting the Unit, Tag Number, and Tag Comment
    • Setting the User-Defined Constant
    • Importing Expressions
    • Importing User-Defined Constants
    • Importing Tag Numbers and Tag Comments
    • Setting Timers (Only When Using Timers in the Computations)
    • When Calculating ±Overrange Values of Measurement Channels as the Maximum or Minimum Value of the Measurement Range
    • Resetting Computation
    • When Setting Computations for Each Channel Individually
  • 2.6 Setting Alarms
  • 2.7 Digital Output
    • Setting the Digital Output of Alarms
    • Setting the Digital Output Other Than Alarms
    • Changing the Manual DO Name and Specified Output
  • 2.8 Analog/PWM Output Settings
    • Setting Analog Output
    • Setting PWM Output
    • Editing Pattern Output
    • “Generate Automatically” Function
    • Turning Transmission Output ON and OFF Collectively for Analog Output/PWM Output
  • 2.9 Event Processing
    • Setting Alarm Events
    • Setting Up Data File Events
    • Setting Communication Events
    • Setting Start Record Events
    • Setting Stop Record Events
    • Configuring FTP
    • Configuring E-Mail
    • User File Settings
    • Enabling/Disabling Events
  • 2.10 Starting/Stopping Data Monitoring and Displaying the Monitor
    • Start Data Monitoring
    • Stop Data Monitoring
    • Displaying the Trend Monitor Window and Changing Display Settings
    • Displaying the Numeric Monitor Window
    • Displaying the Meter Monitor Window
    • Displaying the All Channel Monitor Window
    • Displaying the Alarm Monitor Window
    • Changing Display Settings on the General Display Settings Window
  • 2.11 Pausing/Resuming the Updating of the Monitor Display and Reading Measured Values Using Cursors
    • Pausing and Resuming the Updating of the Monitor Display
    • Reading Measured/Computed Values Using Cursors
  • 2.12 Starting and Stopping Data Recording
    • Starting the Recording
    • Stopping the Recording
  • 2.13 Saving/Loading and Printing Setup Data (Project)
    • Saving Setup Data (Project)
    • Loading Setup Data (Project)
    • Printing Setup Data
    • Print Preview
    • Setting Up the Printer
  • 2.14 Setting Up the Monitor Server
    • Starting and Exiting the Monitor Server
    • Changing the Port Number
  • 2.15 Setting Up the DDE Server
    • Starting and Exiting the DDE Server
  • 2.16 Displaying the Software Version and Other Information
• Chapter 3 Viewer
  • 3.1 Loading Data Files
  • 3.2 Setting the Display
    • Changing the Display on the Waveform Display Window
    • Changing the Display Using the Toolbar
    • Changing the Display Using the Menu
    • Changing the Display Using the Display Settings Window
  • 3.3 Reading Values Using Cursors
    • Clearing Cursors
  • 3.4 Statistical Computation over an Area of Measured/Computed Data
  • 3.5 Saving Display Settings
    • When Closing the Viewer
  • 3.6 Saving the Display Template
    • Saving Templates
    • Using Templates
  • 3.7 Converting Data Formats
  • 3.8 Printing Data
    • Setting the Contents to Be Printed
    • Executing the Print Operation
    • Print Preview
    • Setting Up the Printer
  • 3.9 Displaying the Software Version and Other Information
• Chapter 4 Calibrator
  • 4.1 Connecting the MX100 Data Acquisition Unit
    • When Setting a Password for Startup
  • 4.2 Calibration Procedure
• Chapter 5 Troubleshooting
  • 5.1 Troubleshooting
  • 5.2 Error Messages and Their Corrective Actions
    • Error Messages on the Logger
    • Error Messages on the Viewer
    • Error Messages on the Calibrator
• Index