Brocade Unified IP MIB Reference (Supporting FastIron Releases 07.5.00 and 08.0.10) - Manual (Page 459)

Unified IP MIB Reference 433
53-1003106-01
MCT cluster table
43
brcdMctClusterActiveMemb
erVlans
brcdIp.1.1.12.1.1.2.1.9
Syntax: DisplayString Read-only The list of the active member VLANs of the MCT cluster.
•
The VLANs that are not sequential are represented as
separated by a space; for example, 2 5 100.
•
The VLANs that are continuous and sequential are
represented as a range; for example, 10 to 40.
brcdMctClusterDeploy
brcdIp.1.1.12.1.1.2.1.10
Syntax: BrcdDeployStatus Read-create The administrator status of the MCT cluster.
The consistency check of the entire cluster configuration is done
when the object is set to the deploy(1) value. After the cluster is
deployed, the configuration cannot be modified except for the
brcdMctClusterMemberVlans, brcdMctClusterClientIsolationMode,
and brcdMctClusterDeploy objects.
Default: undeploy(2)
brcdMctClusterDeployFailur
eReason
brcdIp.1.1.12.1.1.2.1.11
Syntax: Integer Read-only The last failure reasons for the cluster deploy operation through
SNMP.
The following failure reason codes are supported:
•
none(1)—Indicates the last deploy is successful.
•
unknown(2)—Indicates the last deploy is failed for an unknown
reason.
•
rBridgeIdNotConfigured(3)—Indicates the remote bridge ID is
not configured.
•
sessionVlanNotConfigured(4)—Indicates the session VLAN is
not configured.
•
iclNotConfigured(5)—Indicates the Inter-Chassis Link (ICL) is
not configured.
•
peerNotConfigured(6)—Indicates the peer is not configured.
•
iclIsMrpSecondaryInterface(7)—On the Brocade NetIron CES
and Brocade NetIron CER series devices, the ICL should not be
a Metro Ring Protocol (MRP) secondary interface.
•
iclIsErpRplInterface(8)—On the Brocade NetIron CES and
Brocade NetIron CER series devices, the ICL should not be a
Ethernet Ring Protection (ERP) Ring Protection Link (RPL)
interface.
•
iclIsErpMsInterface(9)—On the Brocade NetIron CES and
Brocade NetIron CER series devices, the ICL should not be a
ERP MS interface.
•
iclIsErpFsInterface(10)—On the Brocade NetIron CES and
Brocade NetIron CER series devices, the ICL should not be a
ERP FS interface.
•
iclNotInSessionVlan(11)—Indicates the ICL is not in the
session VLAN.
•
iclNotInMemberVlans(12)—Indicates the ICL is not in the
member VLANs.
•
nonIclInterfacesInSessionVlan(13)—Indicates none of the ICL
interfaces are present under the session VLAN.
•
mgmtVeNotConfiguredInSessionVlan(14)—Indicates the
management VE is not configured in the session VLAN.
•
mgmtIpNotConfiguredInSessionVlan(15)—Indicates the
management IP is not configured in the session VLAN.
•
mgmtIpIsUsedInPeerOrClientConfig(16)—Indicates the
management IP is used in peer or client configurations.
•
mgmtIpNotInSubnetOfPeerIp(17)—Indicates the management
IP is not in the subnet of a peer IP.
Name, OID, and syntax Access Description