Aiphone AXW-AVR - Manual (Page 5)

CONFIGURATION DIAGRAM:
AXW-AVT / AXW-AVR with Infinova Fiber (N3732TA-M/-R, N3732RA-M/-R), 1 of 2
Pg. 7 Pg. 8
CCTV Camera
75 Ohm, 1V Peak-to-peak
(Independently powered)
Normally Closed input for remote activation
(i.e. motion sensor, loop detector, etc.)
Normally Open contact for remote device activation
(i.e. video switcher, DVR, etc.)
AXW-AVT
24V
+
-
RELAY
NO
NO
SENSOR
NC
NC
CALL IN
+
-
CALL OUT
+
-
AUDIO IN
+
-
AUDIO OUT
+
-
DOOR
VIDEO IN
VIDEO OUT
AX-DV
AX-DM or IE/IF-Series
Audio Door Station
CAT-5e
Coax
*
+
-
PS-2420UL
Infinova
N3732TA-M
Please Note:
Only information pertaining to the connection and operation of the AXW-AVT / AXW-AVR and listed 3
rd party devices interfacing with it are included here. Aiphone is not
responsible for attempts to connect the AXW-AVT / AXW-AVR to untested 3 rd party transmission hardware. Consult the installation manual for the 3 rd party device being utilized
for further information regarding physical mounting, base functionality, power requirements, etc. For the most up-to-date compatibility information, please consult http://
www.aiphone.com or contact Aiphone Technical Support.
For complete AX system installation, wiring, and programming information, please consult the AX Installation Manual (included on CD with AX Central Exchange Unit, or
available at http://www.aiphone.com).
PWR
V
OP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Optic Fiber
(to N3732TA-M, Pg. 9)
Configuration Notes (1 of 2):
1. AX-series video door station connects to ‘DOOR’ input of AXW-AVT. Ensure
that the “CCTV / DOOR’ switch on the AXW-AVT is in the ‘DOOR’ position.
*2. Alternatively, an IE/IF-series or AX-DM audio door may be used, along with
3 rd party CCTV camera. Connect audio door station to ‘Door’ input (following
the wiring method shown in the AX-series installation manual, pg. 12).
Connect the camera to ‘Video In’ and put the ‘CCTV / DOOR’ switch in the
‘CCTV’ position.
3. Connect the Call In / Call Out and Audio In / Audio Out connections on the
AXW-AVR to the terminal block of the Infinova N3732TA-M, as shown. For
detailed terminal definitions, consult the Infinova installation document.
Configuration Notes (1 of 2, continued):
4. When the SENSOR input is used, the
door station will be turned on whenever
the sensor device is activated (Normally
Closed contact from 3
rd party supplied
device).
5. The RELAY output provides an optional
Normally Open dry contact output which
is activated whenever the AX-series door
station is in use. This can be used to
activate any device local to the AXW-AVT
(DVR trigger, video switcher activation,
local call indication, etc.).
6. Configure AXW-AVT internal jumpers as
necessary (see Pg. 21).
Coaxial Video Cable
**The Infinova N3732TA provides only a
single relay output, which may be used to
control the door station’s standby mode
(when connected to the ‘Call Out’ terminals
on the AXW-AVT), or for door release. If
utilized for door release, ensure that the
‘Call Out’ terminals on the AXW-AVT are
shorted together. Note: This will cause
the door station to be in a constant-on
state, which may reduce the lifespan of
the AX-series door station.
** **