Electrolux EI30BM60MS - Manual (Page 12)

Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL A1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to
3 ⁄
4
″ (19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
Mount Microwave Oven A5.
Adjust Exhaust Adaptor A6.
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST
(Vertical Duct)
A
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
A7. Connect Ductwork
A3.
A4. Check Damper Operation
Adapting Microwave Blower for
Outside Top Exhaust
EN-12
3/8" TO EDGE
%#76+10Ä+(':*#75 6#&#2614+5215+6+ 10'&1765+&' 4'%1//'0&'&&+/ '05+10)4'#5'Ä.#& '0#+49+.. &+5%*#4)' +061*175'5647%6 74'
/+0+/7/9+&6*4'3 7+4'&
4'#49#..6'/2.#6'
NOTE: IT IS VERY I MPORTANT TO READ AND FOLLO W THE DIRECTION S IN THE INSTALLATI ON INSTRUCTIONS BEFORE PROCEEDI NG WITH THIS REAR WALL TEMPLA TE. This Rear Wall Templ ate serves to position the bottom mounting plate and to l ocate the horizontal ex haust outlet.
1. Use a level to chec k that the template is po sitioned accurately. 2. Locate and mark at least one stud on the left or right side of the cen terline. 016' It is important to u se at least one wood screw mounted firmly in a stud to support th e weight of the microwave. Mar k two additional, even ly spaced locations for the suppl ied toggle bolts. 3. Drill holes in the mar ked locations. Where there is a stud, drill a 3/16" hol e for wood screws. Fo r holes that do not line up with a stud, drill 5/8" holes for toggle bolts. 016' DO NOT INSTA LL THE MOUNTING P LATE AT THIS TIME.
4. Remove the templa te from the rear wall. 5. Review the Installati on Instruction book fo r your installation situation.
Locate and mark holes to align with holes in t he mounting plate.
IMPORTANT:
LOCATE AT LEAST
ONE STUD ON EITHE R SIDE OF THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONA L, EVENLY SPACED TOGGLE BOLTS IN THE MO UNTING PLATE AREA. Locate and mark holes to align with holes in the mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EIT HER SIDE OF THE CENTERLINE.
MARK THE LOCATIO N FOR 2 ADDITION AL, EVENLY
SPACED TOGGLE BOLTS IN THE MO UNTING PLATE
AREA. Trim the rear wall tem plate along the dott ed line.
Trim the rear wall t emplate along the dotted line.
%
(%76176(14*14+<106#. 1765+&'':*#756
%76*1.'6*417)* 4'#49#..(14':* #756#&#2614
12"
4"
Darle vuelta a la hoja para consultar la versión en Español.
IMPORTANT :Do not remove the cardboard
spacers between the heat shield and door.