Electrolux EI30BM60MS - Manual (Page 16)

INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
been properly routed and secured,
and that the wires are not pinched.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Back of
Microwave
Installation Instructions
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST B1.
You need to cut an opening in the rear wall for
outside exhaust.
•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
B2.
OUTSIDE BACK EXHAUST
(Horizontal Duct)
B
Blower Plate
REMOVE BLOWER PLATE
B2. Remove Blower Plate
3/8" TO EDGE
     
    
      
NOTE: IT IS VE RY IMPOR TANT TO READ AND FOLLOW TH E DIRECTIONS IN THE IN STALLATIO N INSTRUCTIO NS BEFORE PR OCEEDING WITH THIS REAR WALL TEMPLATE . This Rear Wall Template serv es to position the bottom mounting plate a nd to locate the horizontal exhaust outlet. 1. Use a level to check that th e template is posi tioned accurat ely. 2. Locate and mark at least one stud on the lef t or right side of the centerline. It is important to use at least one woo d screw mounted firmly in a stud to support the weight of the microw ave. Mark two additional, evenly spaced locations for the supplied toggle bolts. 3. Drill holes in the marked locations. Wh ere there is a stud, drill a 3/16" hole for wood screws. For hol es that do not li ne up with a stu d, drill 5/8" hole s for toggle bolts. DO NOT INSTALL THE MOUNT ING PLATE AT THIS TIME. 4. Remove the template from the rear wall. 5. Review the Installation Instruction boo k for your installation sit uation.
Locate and mark holes to align with ho les in the mounting p late. IMPORTANT: LOCATE AT LEAST ON E STUD ON EITH ER SIDE OF THE CENTER LINE. MARK TH E LOCATION FOR 2 ADDITIONAL , EVENLY SPACED TOGG LE BOLTS IN THE MOU NTING PLA TE AREA.
Locate and mark holes to align with h oles in the mounting plate . IMPORTA NT: LOCATE AT LEAST ON E STUD ON EIT HER SIDE OF
THE CENTER LINE. MARK TH E LOCAT ION FOR 2 ADDITIONAL , EVENLY SPACED TOGG LE BOLTS IN THE MOU NTING PLA TE
AREA.
Trim the rear wa ll template a long the d otted line.
Trim the rear wall template along the dotted line.








    
12"
4"
Darle vuelta a la hoja para consul tar la versión en Españ ol.
Make sure the motor wiring has
EN-16
3/8" TO EDGE
%#76+10Ä+(':*#75 6#&#2614+5215+6+1 0'&1765+&' 4'%1//'0&'&&+/ '05+10)4'#5'Ä.#& '0#+49+.. &+5%*#4)' +061*175'5647%6 74'
/+0+/7/9+&6*4'3 7+4'&
4'#49#..6'/2.#6'
NOTE: IT IS VERY I MPORTANT TO READ AND FOLLO W THE DIRECTION S IN THE INSTALLAT ION INSTRUCTION S BEFORE PROCEEDI NG WITH THIS REAR WALL TEMPLA TE. This Rear Wall Templ ate serves to position the bottom mounting plate and to locate the horizontal e xhaust outlet.
1. Use a level to chec k that the template is po sitioned accurately. 2. Locate and mark at least one stud on the left or right side of the center line. 016' It is importan t to use at least one w ood screw mounted firmly in a stud to support th e weight of the microwave. Mar k two additional, even ly spaced locations for the suppl ied toggle bolts. 3. Drill holes in the mar ked locations. Where there is a stud, drill a 3/16" hol e for wood screws. Fo r holes that do not line up with a stud, drill 5/8" holes for toggle bolts. 016' DO NOT INS TALL THE MOUNTIN G PLATE AT THIS TIME.
4. Remove the templa te from the rear wall. 5. Review the Installa tion Instruction book for your installation situation.
Locate and mark holes to align with holes in t he mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATIO N FOR 2 ADDITION AL, EVENLY
SPACED TOGGLE BOLTS IN THE MO UNTING PLATE
AREA. Locate and mark holes to align with holes in t he mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EIT HER SIDE OF
THE CENTERLINE.
MARK THE LOCATIO N FOR 2 ADDITION AL, EVENLY SPACED TOGGLE BOLTS IN THE MO UNTING PLATE AREA. Trim the rear wall tem plate along the dott ed line.
Trim the rear wall tem plate along the dotted line.
%
(%76176(14*14+<106#. 1765+&'':*#756
%76*1.'6*417)* 4'#49#..(14':* #756#&#2614
12"
4"
Darle vuelta a la hoj a para consultar la versión en Español.
IMPORTANT :Do not remove the cardboard
spacers between the heat shield and door.